Jump to content
SAU Community

S A U - N S W Tech Night For Members 24Th Apr - Engine Builds


Recommended Posts

What time you going past pennant hills road you reckon Matt?

Who you coming down with?

Ummmm Leaving here 4.30ish so i guess 5.45 maybe?

Carmen will be following me so we can drive her car home....

  • Replies 195
  • Created
  • Last Reply

Top Posters In This Topic

Double Demerits has begun.

.... =|

Thanks for the heads up, this is not good to hear. This means many cops will be camped out on the F3

Also, should I take the M2/M7 after turning off to Hornsby..... or will it be quicker if I avoid toll roads? I will hit the Hornsby turn off at about 5ish

We will be doing the speed limit and staying stealth.... They should not bother us if nothing wrong is being done!

Temperature drops to 10 degrees tonight.

Your Mums want youz to take a warm jacket.

:P

Oh sheeeeet! I might grab my Snap On jacket if i can find it lol

Been a while since its been nice and cool! Car will love it!

finished for the day aww yea

Again.................. Basterd :P

All you mongrels will rock up all fresh and ill be stressin out of my noodle just trying to get there lol

Again.................. Basterd :P

All you mongrels will rock up all fresh and ill be stressin out of my noodle just trying to get there lol

lol time to hit the gym for some squats BRAH its leg day lol

lol time to hit the gym for some squats BRAH its leg day lol

I noticed Benji is skipping this as ALWAYS :P

Tee Hee :ph34r:

Oh sheeeeet! I might grab my Snap On jacket if i can find it lol

Been a while since its been nice and cool! Car will love it!

hmmm, dare I wear my snap on jacket?
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...