Jump to content
SAU Community

Recommended Posts

Since the day i picked up my car i have had this issue with the bonnet rubbing with the fender and i am finally getting around to fixing it up..

The cause of this rubbing is the hinge itself, somehow it's bent causing this to happen..

Here's a picture of what the bonnet corner/fender looks like after 12 months of rubbing.

foq6up.jpg

ioeykk.jpg

It's not noticeable until you get up close, then it looks horrible. I have tried putting washers behind the bolt holding the hinge in to give the bonnet a bit of height but i can't seem to get it to line up with the fender without it rubbing and it looks silly having it too high.

Now, what my problem seems to be is sourcing a new bonnet hinge. I have been in contact with my buddy Charles from B2Autodesigns in the states but he thinks the guys at OCinfiniti reckon they are different. It's hard to tell between pictures without having the hinge off the actual car but here's a pic of it on my car compared to what i found on google for a g35 hinge.

1zbf288.jpg

64ie6q.jpg

I would go ahead and order a new set of hinges and pay $100 but i'd rather make sure they will actually fit the car. I also plan to get the corner touched up once i've replaced the hinges as it looks horrible and i hate it :/

My local Nissan could be an option, but my experience with those guys has been nothing but negative. Ever since the head service manager told me i need to take the car to a panel beater to get a compression rod bush replaced...

If anyone could shed some light on this that'd be great,

cheers

Edited by Seano350GT
Link to comment
https://www.sau.com.au/forums/topic/421226-bonnet-hinge-rubbing-issue/
Share on other sites

I'm going to be ordering a pair of hinges from Perry Infiniti soon. I can't see why they would be any different to the G35 hinges.

It's a very common problem as highlighted on http://g35driver.com/forums/interior-exterior/216502-another-hood-hinge-bending-problem.html

Andy, thanks heaps for that link i didn't realise how common this issue was. First time i saw it i thought to myself "shit it's been in an accident" lol.

I don't see why they'd be different either, it just seems to look like they are judging by the pictures. Not sure if i should go ahead and buy the hinges from the U.S yet. I might give Nissan a ring today and see if they can help but i highly doubt it.

Amazingly enough, Nissan came through. Must be a new bloke that works at my local Nissan because he's the first one to actually know what a V35 is lol.

$65 for a set of hinges coming from Melbourne so that's good news. My next issue is apparently you have to remove the fender to get the hinges undone.. that sounds like fun.

turns out it's actually a really common problem with the hinges starting to bend.. quite weird if you ask me. But yeah i need to see if it can be done without removing the fenders, after some reading on g35driver.com it seems the fender has to come off. But in saying that a bunch of people were also commenting saying no you don't have to take it off.. we'll see lol.

reminds me on a grandpa's lancer i worked on once, bonnet was hard to open, turns out both hinges were rusted solid. i was actually bending them when opening and closing the bonnet, and the passenger side was already becoming soft and ready to snap

Edited by junkie

had a good look at mine today. seems like the longer part of the hinge, between the pivot point and the bonnet, has some flex in it, you can actually spot it when opening the bonnet

with that amount of flex, if the pivot point isnt lubricated properly, it would flex enough to catch the corner of the guard, and only on the way up

the pivot point itself appears to be in an area with a bit of water runoff from the a-pillar area, so regular lubrication would be a good idea

you can reach it with a thin tube between the a-pillar/guard and lower windscreen trim panel, there is just enough gap there

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
×
×
  • Create New...