Jump to content
SAU Community

Fs: Bolt On 220 - 230 Rwkw Kit, Tuned Pfc, 550Cc, Z32, Highflow Turbo Also Separate Profec B

SKiT_R31
 Share

Recommended Posts

SKiT_R31 Experienced

SKiT_R31

Posted
Posted

Hey All,

I have everything you need to give your standard RB25 / R33 at least 220RWKW, people have been known to get upwards of 240kW out of this particular turbo.

The PowerFC has been tuned for this setup, it was originally tuned for an R34 (OP6) Highflow making 250kW at the treads, but that setup proved too laggy and the power sacrifice is probably worth it for the 1000rpm quicker spool time, the tune has only been adjusted in the lower rpm with ignition timing removed due to the quicker spool time.

The PFC was tuned with the Z32 AFM and the JECS 550cc injectors, both which were new at the time of installation and have done maybe 10,000kms. The turbo is a GCG R33 highflow (not OP6) with zero shaft play and is a direct bolt on replacement. I have only ever run this turbo on 12psi due to only having the factory dump pipe installed at the time of dyno (and as you can see, holds strong), the turbo is good for 14psi but I never had the chance to run that before the car was written off.

I would recommend the ignition timing be set to 15BTDC, an upgraded fuel pump (040, Walbro 255, GTR, etc), boost controller and FMIC be installed with these components, then this should go straight on the car without issues, tune adjustment on the dyno might yield slightly more power for the less aggressive turbo but as is the tune is safe and reliable.

Pictures are attached, the injectors are still in the engine to keep then clean, i will individually snap lock bag them for postage. Note, the second graph is of the original tune for the OP6 highflow, first is with all the gear listed as dyno'd with a greddy profec b, Bosch 040, generic pod filter, standard coilpacks, ebay FMIC kit and 3" exhaust with stock dump.

I'm after $2000 posted (registered/insured) for the Highflow turbo, Tuned PFC, 550cc Injectors and Z32 AFM with plug



SKiT_R31 Experienced

SKiT_R31

Posted
  • Author
Posted

I also have a Profec B Spec II boost controller, matched to the setup which i wanted to sell separately, after $250 posted.

http://img547.imageshack.us/img547/4977/image009j.png

SKiT_R31 Experienced

SKiT_R31

Posted
  • Author
Posted

Hey, I will separate but the fewer packages/trips to the post office the better.

Chillzi, I would be after $1200 posted for those parts combined.

  • 7 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • GTSBoy
      33 GTR Broken front wheel knuckle

      By GTSBoy · Posted

      That's probably OK. That's a face to face compression joint between two surfaces with the clamping load provided by those bolts. So.... it's unlikely that the bolts will end up feeling that load in shear, unless the clamping surfaces are not large enough, bolts not got enough tension on them, etc etc to prevent the two faces from moving wrt each other. Which... I would hope the designers have considered, seeing as it's probably one of the most important things the upright has to do apart from resist collapsing in its own right. But yes, it would definitely be worth asking them what their safety factor on that part of the design was. I tend to think that the casting, being a casting, is not necessarily the strongest bit of material in the world. It's about an inch square, and when you think about the loads that are being put into it, you have to wonder what safety factor the Nissan boys (and every other OEM engineer who has designed all the millions of other uprights that look essentially the same) used to account for defective casting, aging, severe impacts on the wheel, etc etc. 
    • R32 TT
      33 GTR Broken front wheel knuckle

      By R32 TT · Posted

      Those bolts would be orders of magnitude stronger that cast aluminium though.  And its mainly clamping force, not shear they are dealing with?
    • MBS206
      33 GTR Broken front wheel knuckle

      By MBS206 · Posted

      Except all that twisting force that is breaking a cast piece, appears to be going through 4 bolts in the picture Johnny posted of the BryPar one...
    • GTSBoy
      R34 auto to manual conversion help

      By GTSBoy · Posted

      The smart approach is to use the gearbox loom from the manual car. Makes it a lot easier - just plugs into the switches on the box and plugs into the main loom up near the fusebox. Then you only need to deal with bypassing the inhibit switch. The other approach requires you to use the wiring diagram to identify those wires by colour and location, perhaps even indulging in a little multimeter action to trace them end to end to make sure, and then.... you will have the answers you need. The R34 wiring diagram is available on-line (no, I do not have a link to it myself - I would have to do a search if I wasn't able to go to the copy I have at home).
    • Manur33
      R34 auto to manual conversion help

      By Manur33 · Posted

      Hi, i’m converted my r34 4dr auto to manual but need help with gearbox wiring. There are bunch of wires no idea which one for speedo drive, neutral, reverse can anyone help me. IMG_6860.mov
×
×
  • Create New...