Jump to content
SAU Community

Recommended Posts

Found that my check engine light will come on sometimes after prolonged periods of high revs (when drifting at track or last night for a short moment on a mountain drive).

When the light comes on I can't hear knock and the car does not run any differently. I also found that if I touch the accelerator pedal the light will go away straight away. After a drifting run the light is on if I let the revs drop down slowly the check engine light will disappear without me doing anything once the revs get below around 2500-3000.

It seems like a very strange problem and am just worried about causing damage to the engine more than anything.

I have:
Rb25det Neo
Full exhaust
Splitfire coilpacks
ARC FMIC
Nistune

also have but already noticed this problem before installing/tuning for:
z32 AFM
ATR43 G2.5
Bosch 023

Would the check engine light come on if there was a fault with the O2 sensor? Main reason I ask this is a long time ago the plug to my O2 sensor was badly melted yet it all seemed to work fine so I tucked it away from the exhaust so it wouldn't melt further and haven't really had any problems to indicate it isn't working under normal circumstances (I get normal economy for a r34)

Link to comment
https://www.sau.com.au/forums/topic/423037-r34-check-engine-light/
Share on other sites

i would put my money on that the o2 sensor is playing up / overheating

had the same issue with my R34, whenever i would take it for a spirited drive or a power run on a motorway i would get the engine malfunction light - replaced the o2 sensor, cleared the ECU, never had the error light come back since

would go with a genuine Nissan item which is available at kudos motorsports;

http://www.kudosmotorsports.com/catalog/nissan-lambda-oxygen-sensor-genuine-nissan-skyline-r34-25gt-25gt4-25gtt-rb25de-rb25det-neo-p-187.html

i would put my money on that the o2 sensor is playing up / overheating

had the same issue with my R34, whenever i would take it for a spirited drive or a power run on a motorway i would get the engine malfunction light - replaced the o2 sensor, cleared the ECU, never had the error light come back since

would go with a genuine Nissan item which is available at kudos motorsports;

http://www.kudosmotorsports.com/catalog/nissan-lambda-oxygen-sensor-genuine-nissan-skyline-r34-25gt-25gt4-25gtt-rb25de-rb25det-neo-p-187.html

Will give a new one a go I have a good idea that it is 90% likely the issue is from the O2 sensor and nothing else. Unfortunate the error code doesn't remain long enough for me to check it without a laptop plugged in like GTSboy recommends

I'm surprised no one has told you this already. Basically the 2 common ways are u can use a Nissan consult cable and hook it up to a laptop with the right program, or you can get the car to go into self diagnostic mode and spit out the code via flashing lights

I would have lent you my consult but Im in syd.

But the second flashign light method method is just as easy

Search for the Service manual online, or have a look at this thread.

http://www.skylinesaustralia.com/forums/topic/266512-reading-nissan-fault-codes-ecu-fault-codes-how-read-them

That should be enough.

Edited by sonicz

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Starter motors used to use the weight of metal (magnets) to provide torque. Now they use (more) current instead. This. It's completely normal.
    • So thing that had me stumped, but I think is OK....is that when it was up in the air, in neutral I had it running to bleed to coolant while I put the wheels back on. I noticed the rears were turning (slowly) which I'd never seen before 20250928_163512.mp4     Because there had been an issue with clutch slip due to pedal adjustment on the dyno, I assumed there was still and issue so spent some quality time upside down under the dash adjusting the pedal....but no matter what I did the wheels still turned in neutral. Even disconnected the master cylinder to pedal rod and same. In despair, I even removed the clutch slave so there was no chance of any preload causing it.....still happened. So either: 1. Something is not right in the bellhousing, or 2. Its a thing sometimes with cold, thick gearbox oil Internet says it might be 2, I hope so!
    • OK, few more things sorted and it is ready for a shakedown on 10-Oct, with one weird thing. Changed the run in oil and filter for the good stuff. 8l came out, about 8.5 went in with filter so that looks all good. Changed the starter (again), this time for a brand new one, works good. Interesting that the Taaaarks one is shorter than factory but spins harder, I guess electronics have moved on a little in the last 30 years. Will be nice to have a bit of extra space under there. Put the timing cover back on, and noted where the cam gears were set as a record.  Will need to double check the timing but it is pretty close. Also put the coil pack cover and intake snorkel back on. Exhaust Inlet Changed the water out for coolant, bled up nicely. Removed the rear brake pads (well worn factory sumitomo ones!), gave the hardware a good clean and reassembled. I've put bendix XP on the back again because the price is excellent at $150 a set and they worked well on the V37. Front pads have plenty so no issue there
    • Mine is all -12, I’m running a dry sump in a billet block though 
×
×
  • Create New...