Jump to content
SAU Community

Recommended Posts

was intrested in know the first signs of a clutch shitting itself.

the other nite i was at a mates workshop n pulled a nice burnout, but when i changed in second there was major slippage! i took my foot of the accelerator 4 a sec then put it back on n still it was slipping, anyways when i got home it stunk so bad, (not the normal clutch smell) 10x worse.

when driving normally theres no problem, but when i boot it, it feels a lil slower than it should b goin at higher revs,

also when i down gear into 2nd doin round 50km/h i can smell the clutch again.

is my clutch on its way out?

should i start saving 4 another?

or do i still have a while b4 it will need changing?

thanks in advance

john

Link to comment
https://www.sau.com.au/forums/topic/42327-clutch-issues/
Share on other sites

smells like fish when frying the clutch.

You can tell if you drive at like 60k's, put it in 5th gear and floor it. If the revs jump but speed doesn't, then you're in trouble. if not you could be aight for a while.

Also, rev the car up to like 5000-5500 before changing and see if the revs jump up then settle back down. If they do jump up, then its slipping.

Link to comment
https://www.sau.com.au/forums/topic/42327-clutch-issues/#findComment-865211
Share on other sites

Yeah I had the same thing, it felt a little funny on the way to work (~40km), and I almost didn't make it home... It happened as got a near perfect launch the previous day, and burnt the stock clutch from excess slippage on take off. The was still a bit of meat on the clutch, but I had glazed it so bad, there was barely any friction.

My advice is NOT to accelerate hard under any circumstances to prolong it until you have a chance to change it, otherwise your car will soon be undriveable...

Link to comment
https://www.sau.com.au/forums/topic/42327-clutch-issues/#findComment-867428
Share on other sites

mate the same thing happened to me once, what i think you have done is glazed the surface of your clutch...u might still have a fair bit on it but you will need to change it sooner or later... Soon after that happened in the mornings the clutch would shudder a bit untill it warmed up, you will have a month or so of use, but it will start pissing you off soon so an exedy single plate is a good idea...

Link to comment
https://www.sau.com.au/forums/topic/42327-clutch-issues/#findComment-874395
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
    • Actually, I'd say all three are the automatic option. Just the different trim levels. The manual would be RSFS, no? 
×
×
  • Create New...