Jump to content
SAU Community

Recommended Posts

Hey there,

I have a r32 GTR and was wondering what the oil pressure guage on the dash should read? It seems to fluctuate from near 4 on cold start, to almost zero when freeway cruising. It doesn't seem right to me. I have searched but was chasing some more recent info - especially on places to get it done.

I have looked at aftermarket oil pumps - n1 around $250 - $300, JUN, NISMO - $1300. I don't want to get big power out of the motor so would a n1 be enough? I don't fancy spending a grand if theres no need for it.

My last question would be, has anyone recently (as mechanics leave etc..) had an oil pump changed, as i've heard the front diff needs to come out. Any places you'd recommend?

Cheers,

Any help is appreciated.

Link to comment
https://www.sau.com.au/forums/topic/424456-r32-gtr-oil-pump-sensor-reading/
Share on other sites

Probably is the pressure sender, I've never heard of an oil pump to let you know it's about to fail. They just break

I used a N1 oil pump with remax gear set and I'm hauling close to 400 awkw. The gear set is around $450 delivered plus

N1 pump, it should all cost around $550,

you will need to put a restrictor in the head though, and it's motor out job

Good luck

Probably is the pressure sender, I've never heard of an oil pump to let you know it's about to fail. They just break

I used a N1 oil pump with remax gear set and I'm hauling close to 400 awkw. The gear set is around $450 delivered plus

N1 pump, it should all cost around $550,

you will need to put a restrictor in the head though, and it's motor out job

Good luck

If you're not going for power, a standard OEM pump would be better than the standard N1 due to the N1s having weak gears - however if you get the remax/reinik/nitto gears to replace it (as suggested above) then you'll be fine - they are extremely strong gears. One thing that is worth checking is where the crank meets the oil pump - if you have an early r32 you'll want to buy a crank collar to prevent drive failure as the early cranks have that area machined too small (its cheap and worth doing if you already have the oil pump off).

Personally, I'd go the route suggested above, get the N1 housing (higher pressure relief valve to OEM) and put the stronger aftermarket gears in it. It all comes down to how much you're prepared to spend.

-D

 

If you're not going for power, a standard OEM pump would be better than the standard N1 due to the N1s having weak gears - however if you get the remax/reinik/nitto gears to replace it (as suggested above) then you'll be fine - they are extremely strong gears. One thing that is worth checking is where the crank meets the oil pump - if you have an early r32 you'll want to buy a crank collar to prevent drive failure as the early cranks have that area machined too small (its cheap and worth doing if you already have the oil pump off).

Personally, I'd go the route suggested above, get the N1 housing (higher pressure relief valve to OEM) and put the stronger aftermarket gears in it. It all comes down to how much you're prepared to spend.

-D

 

If there is nothing wrong with the pump pressure just leave the thing alone.

   

If there is nothing wrong with the pump pressure just leave the thing alone.

Its not a matter of modification, its the default on some pumps -

Below is stolen from http://www.skylinesaustralia.com/forums/topic/227714-rb26-crank-in-rb25/

An early R32GTR "stock" oil pump? The N1 pump has the wide drive flange, the early R32GTR oil pump doesn't, they have the narrow drive flange. The N1 oil pump also has a different rotor configuration and the higher oil pressure relief valve.

A late R32GTR "stock" oil pump? They both have the wide drive flange,but the N1 oil pump also has a different rotor configuration and the higher pressure relief valve

An R33GTR "stock" oil pump? They both have the wide drive flange, but the N1 oil pump also has a different rotor configuration and the higher pressure relief valve

An R33GTR V SPec "stock" oil pump? They both have the wide drive flange and the same rotor configuration, but the N1 oil pump has the higher pressure relief valve

An R34GTR "stock" oil pump? They both have the wide drive flange, the same rotor configuration and the higher pressure relief valve

Hope that helps

-D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...