Jump to content
SAU Community

Recommended Posts

after selling the skyline, i have been driving my mini for a while, although it's very "head turning" :) (seriously!), the reliably is horrible.

then this car come up in the trading post.

i just paid the deposit and it should be mine end of this week :rant:

it's a 2002 S15 Spec S, GT version

with standard leather seat and a few chrome bit

and very low 18000km

modifications

3 inch turbo back exhaust(Exhaust Technology) with titanium end pipe

pod filter

Blitz electronic boost controller SBC-DC

Blitz Front Mount Intercooler

Xtreme Heavy Duty Clutch

Bosch Fuel Pump (GTR Hi-Flow)

Apexi turbo timer

Blitz Boost Gauge

it's pulling 180rwkw@ 1 bar

the same time i already got somethings sitting at my home

a set of 17' 5 zigen deep dish rims

Apexi SAFC

Apexi CAI box

can't wait to criuse with u guy soon!

P.S. the mini is for sale!

u can take it for 3k

it's a 1100cc

with union jack

sunroof

PM me if u are interest :D

Link to comment
https://www.sau.com.au/forums/topic/42502-my-new-ride/
Share on other sites

i still stay in SAU, ppls in NS.com act a bit too young for me... :D

i always love skyline, IF i am an aussie i am sure i will build a RB30 instead of buying this car.

wait till next year when i finish my study and apply for PR, then i might sell this and start build something nice...

Link to comment
https://www.sau.com.au/forums/topic/42502-my-new-ride/#findComment-871248
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
    • Shimmed or shimless, still solid, no hydraulic pump up stuff.
    • They have said food will be limited. Mainly meat pies and sausage rolls from memory. But they have a coffee van!
×
×
  • Create New...