Jump to content
SAU Community

Recommended Posts

  • Replies 44
  • Created
  • Last Reply

Top Posters In This Topic

just an update, put the vac line from the wastegate accuator to the intercooler piping just before the factory pipe that crosses over the motor, and it boosts in almost 500 rpm quicker, cheers for the help guys.

If you're on a budget just put an rb25 turbo in it. You'll have a lot more fun that way. I've been down the rb20 with gt2876 route and the terrible amount of lag got annoying really quick. I tried different wastegate vacuum locations and a smaller ex. housing with no big improvements. The best I got was full boost at 4000rpm with nothing but slug performance before that.

The cheapest way to fix your problem is as Dobz says above and go for a standard RB25 turbo. Though you'd be lucky to hit 200 rwkw.

If you want to stick with the current turbo, you could go for a Mx Performance Exhuast manifold (with 1" runners) and external gate. I have done this with my HKS GT-RS turbo and it has transformed the power delivery. I have also heard of good results with the RB20 (full boost on a GT3076 at 3600rpm) with this manifold setup. Though if you went down this route, you wouldn't get much change out of $2000 once you have it installed and a custom dump made to suit.

By limiting yourself to less than $1000, you don't really have much option other than the RB25 turbo.

Id say from the acuator to the front housing is the best or intercooler piping I guess. Shorter the line the better.

Getting boost signals (gauge or controller) from the manifold would be considered best because then all/any boost drops have been accounted for.

Where as off the housing where the turbo makes say 12psi, by the time it reaches the manifold it may have dropped to 10psi, due to inefficient intercooler design.

  • 2 weeks later...

havent really got much of a chance of buying much, job i have barely covers my bills, let alone 2g on turbo parts, also have to move interstate end of this year so saving is bit more important atm, was looking to find a cheaper way to fix what i have, but guess there aint much choice really :/ will just have to deal with it.

I wouldnt say the hks 2535 is the best for a rb20, i found it abot laggy but went good up top, 2530 is better but alot harder to find one. But both good good for 220kw+

Ifyou found a HKS 2535 laggy on a rb20 then there was something wrong with your setup or you need to find a new tuner.

You could maybe have your compressor wheel taken off and put a gtx67mm wheel on it in the future to make it less laggy. Be cheaper than buying a whole new turbo. I'm sure stao from hypergear will do this for you.

  • 3 weeks later...

living in out rural S.A at the moment but will be heading up to darwin in september to live, but i will keep that in mind once i get up there and find a decent person to work on the car, any one know a decent tuner in darwin for turbos and such?

It would have to be one of garretts biggest mis matched turbos in gt form. I guess there must be a market for them though. I can't imagine how lazy the gtx version would be on a rb20/25. Makes my stomach turn thinking about it haha.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • perhaps i should have mentioned, I plugged the unit in before i handed over to the electronics repair shop to see what damaged had been caused and the unit worked (ac controls, rear demister etc) bar the lights behind the lcd. i would assume that the diode was only to control lighting and didnt harm anything else i got the unit back from the electronics repair shop and all is well (to a point). The lights are back on and ac controls are working. im still paranoid as i beleive the repairer just put in any zener diode he could find and admitted asking chatgpt if its compatible   i do however have another issue... sometimes when i turn the ignition on, the climate control unit now goes through a diagnostics procedure which normally occurs when you disconnect and reconnect but this may be due to the below   to top everything off, and feel free to shoot me as im just about to do it myself anyway, while i was checking the newly repaired board by plugging in the climate control unit bare without the housing, i believe i may have shorted it on the headunit surround. Climate control unit still works but now the keyless entry doesnt work along with the dome light not turning on when you open the door. to add to this tricky situation, when you start the car and remove the key ( i have a turbo timer so car remains on) the keyless entry works. the dome light also works when you switch to the on position. fuses were checked and all ok ive deduced that the short somehow has messed with the smart entry control module as that is what controls the keyless entry and dome light on door opening   you guys wouldnt happen to have any experience with that topic lmao... im only laughing as its all i can do right now my self diagnosed adhd always gets me in a situation as i have no patience and want to get everything done in shortest amount of time as possible often ignoring crucial steps such as disconnecting battery when stuffing around with electronics or even placing a simple rag over the metallic headunit surround when placing a live pcb board on top of it   FML
    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
×
×
  • Create New...