Jump to content
SAU Community

Reducing Lag Rb20 With 2876R?


Recommended Posts

  • Replies 44
  • Created
  • Last Reply

Top Posters In This Topic

just an update, put the vac line from the wastegate accuator to the intercooler piping just before the factory pipe that crosses over the motor, and it boosts in almost 500 rpm quicker, cheers for the help guys.

Link to comment
Share on other sites

If you're on a budget just put an rb25 turbo in it. You'll have a lot more fun that way. I've been down the rb20 with gt2876 route and the terrible amount of lag got annoying really quick. I tried different wastegate vacuum locations and a smaller ex. housing with no big improvements. The best I got was full boost at 4000rpm with nothing but slug performance before that.

Link to comment
Share on other sites

The cheapest way to fix your problem is as Dobz says above and go for a standard RB25 turbo. Though you'd be lucky to hit 200 rwkw.

If you want to stick with the current turbo, you could go for a Mx Performance Exhuast manifold (with 1" runners) and external gate. I have done this with my HKS GT-RS turbo and it has transformed the power delivery. I have also heard of good results with the RB20 (full boost on a GT3076 at 3600rpm) with this manifold setup. Though if you went down this route, you wouldn't get much change out of $2000 once you have it installed and a custom dump made to suit.

By limiting yourself to less than $1000, you don't really have much option other than the RB25 turbo.

Link to comment
Share on other sites

Id say from the acuator to the front housing is the best or intercooler piping I guess. Shorter the line the better.

Getting boost signals (gauge or controller) from the manifold would be considered best because then all/any boost drops have been accounted for.

Where as off the housing where the turbo makes say 12psi, by the time it reaches the manifold it may have dropped to 10psi, due to inefficient intercooler design.

Link to comment
Share on other sites

  • 2 weeks later...

havent really got much of a chance of buying much, job i have barely covers my bills, let alone 2g on turbo parts, also have to move interstate end of this year so saving is bit more important atm, was looking to find a cheaper way to fix what i have, but guess there aint much choice really :/ will just have to deal with it.

Link to comment
Share on other sites

eventally going to go rb25dett, heard they spool up good with good power. ultimate goal is 300rwkw with awesome response and good revvability.

Link to comment
Share on other sites

I wouldnt say the hks 2535 is the best for a rb20, i found it abot laggy but went good up top, 2530 is better but alot harder to find one. But both good good for 220kw+

Ifyou found a HKS 2535 laggy on a rb20 then there was something wrong with your setup or you need to find a new tuner.

Link to comment
Share on other sites

Awesome response mate. Will make will make a 2876r feel like a pos. Basically no different to a rb25 standard turbo in response

Edited by Joshbigt62r
Link to comment
Share on other sites

You could maybe have your compressor wheel taken off and put a gtx67mm wheel on it in the future to make it less laggy. Be cheaper than buying a whole new turbo. I'm sure stao from hypergear will do this for you.

Link to comment
Share on other sites

  • 3 weeks later...

living in out rural S.A at the moment but will be heading up to darwin in september to live, but i will keep that in mind once i get up there and find a decent person to work on the car, any one know a decent tuner in darwin for turbos and such?

Link to comment
Share on other sites

I noticed that there is a GTX2876 available, as if the GT2876 isn't bad enough, why would they even think of creating such a turbo??

What is garrett doing? :wacko:

Link to comment
Share on other sites

It would have to be one of garretts biggest mis matched turbos in gt form. I guess there must be a market for them though. I can't imagine how lazy the gtx version would be on a rb20/25. Makes my stomach turn thinking about it haha.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share




  • Similar Content

  • Latest Posts

    • I’m sure this has been discussed many times. But anyone have any or know someone that is selling genuine N1 rear pods? I’m still shocked no one replicates these yet. Looking to buy some. Added a photo of the part. 👍🏻
    • Hello, The dog bone wont have much to do with this - the calliper applies a load about the disc - the outside of the calliper is more flexible than the inside by virtue of it not haveing the big torqued down bolts, additional metal structure on the caliper itself, and mostly not being cantilevered. So the outside of the calliper is pushing away as its more bendy and brining the inside with it as an equal pressure on both sides of the caliper looks to cause more flex on the outside - which makes sense. I have done this same thing with the calliper unbolted from the dog bone - same thing happens. Although id have to watch more carefully to see how much more the outside moves than the inside in this case. Im guessing there is a point in the pedals travel where the pressure is not actually increasing in the system - its just volumne displacemnt - and because the outside of the calliper is more flexy, it receives that volume. Have gone back to Alcon again - but beyond a resolution there I would stay clear of this calliper and possibly any of the lighweight type of callipers - especially if you have the smaller 15/16" master cylinder. Cheers.
    • Yes, you can very clearly see from more than one angle that it is the whole caliper moving left-right, not deformation of the caliper. The top moves, the bottom moves. Equally. It should be possible to see where the movement is occurring. Just need to look more closely.
    • Hi Folks, my 2009 Skyline 370GT “Crossover” wagon is losing water and has been diagnosed as needing a water pump replacement (it’s an internal timing-chain driven unit, not the usual electric type that seems to be used across many manufacturers). Am looking for any repairer recommendations in the Sydney /Wollongong region who can be trusted and are experienced in this sort of work on the VQ 36 engine. Many thanks….Bill
    • While all of the above makes sense, we're not talking about some Ling Long calipers of AliExpress; Alcon would have to be one of the top 5 caliper suppliers in the world and these are not their budget units. If there were manufacturing defects in the caliper causing this issue I'd be very disappointed. Having re-watched the video a few times I think it's dog bone/mount related. The caliper moves independently to the rest of the suspension and brake assembly which suggests to me that it's not mounted rigidly. I know this sounds stupid, but have you got enough thread on the retaining bolts or are they a poofteenth too long and it's not super tight? For axial movement to be occurring without deforming the caliper that can be the only answer.
×
×
  • Create New...