Jump to content
SAU Community

Recommended Posts

Updating parts list all the time as I find things so keep an eye on the first post. Many parts are not listed yet so just ask as I probably have it.

Prices are ONO so don't hesitate to make fair offers, it's all gotta go!

Located in lower Blue Mountains Sydney, can post/courier most things at cost.


S2 Rs4s Stagea- White

Front drive shafts $130 each
Front hubs $120 each
Manual gearbox $850 (2001 model, has gear stick)
Manual conversion $500 (pedals, handbrake, master/slave, flywheel, clutch and slave)
Manual dash cluster $150
Manual steering wheel with airbag $200
Head lights $350 (no fading)
Radiator (manual) $200
Steering rack and lines $150
Crossmember $100
Dash $100
Passenger airbag $100
Glove box $40
Bonnet $100
Boot with wing $180
Doors $100 each
Front guards $80 each
Brakes $100
ABS unit $100
Strut brace $50 (is slightly bent where another front cut was stacked on top of it)
Front reo $80
Fog lights $60

Neo Rb25det motor parts (parting out due to low compression on number 6):

-Head including covers and complete intake, no turbo $Sold

-Turbo $400

-CAS- sold

-Sump $250

-Block $300

-Spitfire coilpacks $280

-S2 (pink label) AFM $80 plug not included

-Engine loom $150



S1 Rs260 Stagea- white

Interior door trims (RS260 trim) $300 for all four
Front and rear seats (RS260 trim) $TBA depending on condition when I check them out
Complete rear end minus diff and with 32gtr brakes not brembos (sold already) $500
Passenger side headlight $100
Dolphin side skirts and rear bar $250 for both (rough condition)
Rear wing $50
Drivers window switches $80
Passenger window switch $30
Intercooler (stock) $150
Radiator $100
Tail lights $50 pair
Bonnet gas struts $40 pair
Bonnet hinges $30 pair
Front door hinges $30 for the lot
Catch can $20

Dolphin Side skirts and rear bar $120 each, they are in average condition and could do with minor repairs. No postage local pick up only on these (they cost a bomb to send).

Various other parts to be uploaded as I go.

Remember prices are ONO!

post-219-0-48400500-1369282052_thumb.jpg

post-219-0-79920800-1369282054_thumb.jpg

post-219-0-78613400-1369282058_thumb.jpg

post-219-0-00531500-1369282068_thumb.jpg

post-219-0-66531100-1369282070_thumb.jpg

post-219-0-23749600-1369282077_thumb.jpg

post-219-0-40302700-1369282164_thumb.jpg

post-219-0-32850800-1369282167_thumb.jpg

post-219-0-97036000-1369282170_thumb.jpg

post-219-0-51429500-1369282177_thumb.jpg

post-219-0-43745700-1369282180_thumb.jpg

post-219-0-34963700-1369282212_thumb.jpg

post-219-0-91460200-1369282214_thumb.jpg

post-219-0-28528400-1369282217_thumb.jpg

post-219-0-02770700-1369282226_thumb.jpg

post-219-0-98968500-1369282227_thumb.jpg

post-219-0-36159400-1369282230_thumb.jpg

post-219-0-26011800-1369282233_thumb.jpg

post-219-0-82442200-1369282235_thumb.jpg

post-219-0-84254800-1369282238_thumb.jpg

post-219-0-49438900-1369282241_thumb.jpg

post-219-0-62892400-1369282247_thumb.jpg

post-219-0-67393500-1369282249_thumb.jpg

post-219-0-93714000-1369282251_thumb.jpg

post-219-0-15638800-1369282256_thumb.jpg

post-219-0-56314600-1369282258_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...