Jump to content
SAU Community

Recommended Posts

R32 GTS/ GTST / GTR Bolt in Safety 21 6 point cage $400 ono.

Goes around dash. has provisions for cross brace and harness bar in rear legs.

Has nuts and bolts but needs new base plates.

No longer needed as i went a weld in cage.

*Pick up only* or buyer to organise own freight.

post-31951-0-43397700-1368958209_thumb.jpg

R32 GTR Cluster $100 has 45, ooo ish km's on it

(currently in my track car, can get pick if needed)

R32 GTR Front Tailshaft (may fit 33, will not fit r34) $50

post-31951-0-83372100-1368958909_thumb.jpg

R32 GTR Transfer Case (will also fit r33 and r34 gtr) $150

post-31951-0-93598500-1368959067_thumb.jpg

R32/33/34 GTR Front turbo rubber intake pipe $20

post-31951-0-89881500-1368957391_thumb.jpg

R32/33/34 GTR Exhaust Manifold heat shield (only have one) $10

post-31951-0-88825300-1368957982_thumb.jpg

R32/33/34 GTR alloy engine mount (passenger side) $20

post-31951-0-13514100-1368958026_thumb.jpg

Z32 afm plug (used) with length of wire attached $10

post-31951-0-44383100-1368958113_thumb.jpg

R34 GTR Engine Undertray $50

post-31951-0-06626900-1368958532_thumb.jpg

R33 GTST intake pipe with bov return $20

post-31951-0-13480100-1368958722_thumb.jpg

R32 Bare dash pad, has bubble in usual spot on the pass side $20

post-31951-0-73102500-1368959450_thumb.jpg

Brad 0437 198 210

pm or sms / call me.

parts located in upwey vic, can also be picked up from dandenong during the day.

will send smaller items at buyers cost. prefer pick up on the larger items.

Link to comment
https://www.sau.com.au/forums/topic/425527-r323334-gtr-parts-cheap-melb/
Share on other sites

GTRPSI - The car had back seats in with the cage when i got it, but it was a tight sqeeze, you wouldnt want to have passengers in the back.

Steve.b - Send me a pm / sms

Roy - Let me know wenever suits you mate, its in storage so i need a days notice.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..   
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...