Jump to content
SAU Community

Greddy Emanage Ultimate Maps

jase_c

By jase_c,
in Engines & Forced Induction

 Share

Recommended Posts

jase_c Collaborator

jase_c

Posted
Posted

I took my R34 Gtt in to get tuned on monday, the usual stage one mods, (Front mount, 3" exhaust with dump, pod filter, cold air box, apexi avc-r and flowed turbo plus water/Methanol injection and a Greddy Emanage ultimate controlling it) and when my tuner hooked the car up to the laptop the emanage needed an update on the software. As soon as that was done the car shat itself basically and the update either corrupted the emanage or the tune i had in there already. The car would run but wouldnt idle at all and was belching unburnt fuel. I had to bypass the emanage and run off the stock computer to get the car home and now that my maps are corrupted or changed they are basically useless.

I was wondering if anyone out there may have an emanage in their auto Gtt and may be able to help me out by sending me a copy of their map files so i have a reasonable base map to start from again so i am not paying shitloads of dyno time to get my car running well again as i am already down one full days tuning $$ and took a massive step backwards.

Really hope someone can help me out.

Link to comment
https://www.sau.com.au/forums/topic/426032-greddy-emanage-ultimate-maps/
Share on other sites
jase_c Collaborator

jase_c

Posted
  • Author
Posted

If you update the software you need to update the Emanage Ultimate or it won't work. The map should be fine if you still have a copy...

The software on the emanage ultimate was updated thsts what stuffed everything.

Kenna802 Experienced

Kenna802

Posted
Posted (edited)

If you have stock injectors etc.. you don't need a map for it to idle. Is your AFM the normal type for the motor ? And yes you need to do 2 updates one for the software and one for unit.

Please note if you have a laptop with windows 8 good luck... In order for it to work you need non usb 3.0 and since Microsoft only have the drivers for windows 8 it stops them working all together. I found with windows 7 u need a virtual machine running xp with 2.0 drivers ( you can just uninstall the 3.0 drivers and it reverts back to 2.0 )

Sounds like you need to plug your laptop in and connect to your Emanage and check to see if the basics are setup ( engine type..AFM type, CAS angle sensor, ) re do those also are the toggle switches that turn your maps on on the unit turned on? ( the little yellow ones on the side of the unit ) ill send u a pm with my mob no as it easier to talk than to type. Cheers

Edited by Kenna802
jase_c Collaborator

jase_c

Posted
  • Author
Posted

Everything was running fine(and the basics are still setup ) and had been setup since i got the car but after the update it wont run properly and it wouldnt let us in to save the maps before it updated so i have nothing to fall back on or to compare the maps to now so i can pinpoint whether the unit itself is the problem or if it changed the maps or how it is reading them (if that makes sense)

jase_c Collaborator

jase_c

Posted
  • Author
Posted

re updated to 2.20 on both the laptop and the emanage unit and no difference, runs rough and when you blip the throttle it dies, disconnect the emanage and go back to the stock ecu and it runs fine. WTF???

r33canada Community Regular

r33canada

Posted
Posted

i updated mine to 2.30.

and it shat itself the next day. it would idle fine and drive. but when i put my foot down more than half way it would sputter and not rev, so i did the same at the moment, went back to stock for now.

I'll figure it out when i get my car back from my mechanic.

I have a feeling that the update changed something slightly and the car didnt like it. yea i know, thats not a big help and a very big guess. but its all i have.

i'll let you know what i find out.

jase_c Collaborator

jase_c

Posted
  • Author
Posted

yep yours sounds pretty much what mines doing Canada, sort of what i was thinking, that it changed something or maybe the update corrupted something in the units? i changed the maps back to default (all values 0.0) and still the same.

jase_c Collaborator

jase_c

Posted
  • Author
Posted

Yeh im back at 2.20 and it hasn't helped, might try taking each factory sensor off the emanage seperately and running it off the stock ecu to see if that will pinpoint where the problem is in the emanage.

jase_c Collaborator

jase_c

Posted
  • Author
Posted (edited)

So i did a data log on the Emanage today and can see where the problem is, just not whats causing it. When i give the throttle a little blip (around 15%) the output injector duty is hitting 100% and the rpm is only 1300 or so. even when idling the input and output values are a bit different even though the values on the map table are 0.0

Anyone else had problems after the software update that totally screwed the unit?

post-110200-0-39061200-1370248639_thumb.jpg

Edited by jase_c
r33canada Community Regular

r33canada

Posted
Posted

i'll post the links to my data log and what my car was doing. i think i need to start from scratch. set everything back up as if it was the first time.

I had enough issues with v220 and getting my car to run. one thing that i had with my setup was the car wouldnt run right with the settings at stock value for injectors so i have to play with the injector settings up until it would run normal.

what are stock injectors? 370 or something. i think i had to set mine at either 440 or 550 or something. i think it was whatever the gtr stock injectors were.

anyway i will go through it all whenever i get my car back. i was really interested in this update. was liking the fact that autotune was going to work properly on it own. :)

(watch in 720p so you can read it)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Neil's R33 Gts-t Build

      By MBS206 · Posted

      Just as a thought, if it's in neutral, thats your drive line disconnect, not the clutch. Clutch slip at the dyno with pedal fully out, is actually adding a second disconnect. So it's not a clutch issue if you're in neutral. Just a bit of friction dragging the output around while in the air.
    • GTSBoy
      "Cheap" bolt on turbo on RB25DET NEO

      By GTSBoy · Posted

      The HG high flow is excellent, and costs about the $$ you're talking about. But it, and probably every other highflow, uses a diffeent core than the original turo, and the original Hitatchi core is quite long. So, I think it is inevitable that there is likely no such thing as a highflow that just "bolts on" with no other effort required. And the same is likely true for HG's outright replacement "bolt on" turbos (the ATR things). And the same is likely true for anything similar from elsewhere. I have no idea if the cheap Chinese/Taiwanese complete turbos from eBay/Temu/etc are as bolt on as they claim. I mean, they claim the bolt onto the NAs as well as the turbos, and we know that can't be "bolt on". But it wouldn't matter because I'm not buying a $169 4 psi turbo for anything other than a paddock basher.
    • Kapr
      "Cheap" bolt on turbo on RB25DET NEO

      By Kapr · Posted

      Bummer...yeah i "need" something to "ease" up the work and for my driving it would be enough.    Iam counting the tune "without" turbo. I do not mean "cheap" like something from Temu around 200 USD, "Cheap" is something around 1000 USD? 
    • GTSBoy
      Neil's R33 Gts-t Build

      By GTSBoy · Posted

      Starter motors used to use the weight of metal (magnets) to provide torque. Now they use (more) current instead. This. It's completely normal.
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      So thing that had me stumped, but I think is OK....is that when it was up in the air, in neutral I had it running to bleed to coolant while I put the wheels back on. I noticed the rears were turning (slowly) which I'd never seen before 20250928_163512.mp4     Because there had been an issue with clutch slip due to pedal adjustment on the dyno, I assumed there was still and issue so spent some quality time upside down under the dash adjusting the pedal....but no matter what I did the wheels still turned in neutral. Even disconnected the master cylinder to pedal rod and same. In despair, I even removed the clutch slave so there was no chance of any preload causing it.....still happened. So either: 1. Something is not right in the bellhousing, or 2. Its a thing sometimes with cold, thick gearbox oil Internet says it might be 2, I hope so!
×
×
  • Create New...