Jump to content
SAU Community

Recommended Posts

Event:
Happy Laps - Lakeside Park

Description:
A chance to get out on track for a fun cruise and have some om nom noms! Bit of spirited driving is allowed but it is still an event on a race track so a few rules need to be followed (see below). Breakfast will be served with bacon, eggs, beans and toast.

Location:
Lakeside Park
Link To Map.

Date:
Saturday, 15th of June 2013

Time:
7:00 AM Arrival
7:30 AM Breakfast
8:00 AM On Track

Cost:
$35 for members and guests of members riding/driving the members car.

$50 for non members.
Please note that this is a per person cost, any passengers are required to pay as well.
If you wish to come along to watch and not have breakfast it is free.

Requirements:
1. Participants must meet minimum age requirements for being on track. Minimum age: 12yrs old.
2. No overtaking in the first 2 laps.
3. The overtaking car is responsible for completing the overtaking move safely.
4. Overtaking is only permitted on straights, unless clearly waved passed by the car in front.
5. Overtaking move must be completed well before the end of the straight, and the car being overtaken must be given plenty of room.
6. Cars should not be more than 2 abreast at any point on the track.
7. Be aware of cars around you, in front and behind (and beside when being overtaken).
8. Do not assume that the car in front of you knows you are there.
9. Please fill out the attached attendance form and email it to [email protected] SAUQLD___June_Happy_Laps___LP.doc
10. Please pay cash on the day, no EFTPOS is available.
Lakeside Specific Rules:
11. Members only.
12. Members must have completed at least ONE QR Happy Laps before participating in a Lakeside session. (If you have done other Lakeside events before you may be eligible. PM me to clarify)
13. No overtaking or cars side by side on the kink.

Link to comment
https://www.sau.com.au/forums/topic/426254-lakeside-happy-laps-150613/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
    • You think its the AFM? I know its a common issues on R32s. I find it coincidental how this issue raised right after cleaning the fuel system. As everything except the fuel system was fine before. I tried running it with the IACV unplugged but did not notice a difference and still stalled. However, the RPM gauge is not in the cluster right now, so I will need to connect the laptop again and use Nistune to check the RPM. I will check this weekend.
×
×
  • Create New...