Jump to content
SAU Community

Recommended Posts

ok in the last few days my car has been virbrating in the front when doing certain speeds.. its not the gearbox, cause at 100k's when you push the clutch in the nosie is still there. its a consistant nosie with the speed, when you go faster the noise goes faster, if you know what i mean.

could it just be the tires needing an alignment? the front cv's need replacing, could it be that?

the car is a R32 GTS-4.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/42701-front-end-virbrating/
Share on other sites

go wheel alignment @ all 4 wheels. Happened to me when becos i was rushing for time after fitting new tyres and had to rush off for an appointment. The steering wheel was vibrating badly after 100km/h.

it was all good again after i went for a 4 wheel alignment 2 days later.

its not the steering wheels thats doing it.. i can fell it through the pedal. i think its the front right cv.. its got a crack in it so i think i'll be getting new ones to sort that problem.

but on the weekend i put GTR front struts into my car and now there is a big bonk noise whenever you go over a big bump.. NOT COOL!! i was looking at the front left support arm bush things and one of them is ok and the other has half of it hangin over the side.. it wasn't doing this before i installed the front struts?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...