Jump to content
SAU Community

Recommended Posts

yesterday I installed my new tension arms, lower brace, steering rod ends and coilovers ( all japspeed). Fitting was easy, but I'm running into problems aligning everything. I've adjusted the tension arms so the wheel is exactly centered in the arch (a few degrees positive), and trying to adjust toeing now. Strange thing is that the wheels are still facing inwards a bit, but I can't shorten the steering rods any further.. if I push the wheels back with the tension rods, it gets better, but that makes the caster go negative..is there a different way to affect the front toe?

Link to comment
https://www.sau.com.au/forums/topic/427119-r33-gtst-toe-alignment-issues/
Share on other sites

Can't see whats wrong there, it's fitted correctly and the rods should be the correct ones according to japspeed.

20130617_065956_zpsddb676db.jpg

What I'm going to try tonight is raise the car a cm and push the wheels back a bit.
The car used to stand like this:
292363_481995421880150_117211904_n.jpg
Looks like it definately had negative caster, but it's hard to know for sure. Does anybody know the dimensions it's supposed to have horizontally from the center of the wheel to the front and to the rear of the arch?

Edited by sstennizz

10mm longer, so I compensated that on the tread of the rod, .. but then still had to add the rest of the tread.. So it's not really the end that's the problem.
And about the rack ends, what I don't understand is why they'd sell the rod ends if you end up needing different rack ends as well?

My guess is that it has to do with the caster. I'm starting to think the wheel isn't supposed to be dead center in the arch. But slightly to the rear. Though haven't got anything to compare it with. Images I find on google of side views show the wheel damn near dead center, but might be heavily modified..

Have you actually measured caster, or are you just guessing that fore-aft movement results in a certain amount of +/- caster? For one thing, your car may have been owned and driven by a 6-toed moron who liked to crash it into kerbs and the front crossmember might have been moved on it's chassis rail bolts. That can cause the wheels to be fore or aft of where they're supposed to be.

True. I'm going to check the angle today, see where it is exactly. My guess is that is just has to move back a bit. We did some measuring and a degree in caster is barely visible without measuring. We'll see. Planning to have her aligned next wednesday. First have to mount the hicas lockout bar. Better get front and rear done at the same time, instead of having to go twice.. ;)

Things I know for sure:
My front caster is damn near 0 degrees
20130617_163036_zps9087448f.jpg
Pushing it back makes it go negative and improves the toe angle, pulling it forward towards the required 6.4 degrees makes it toe in even more.

My wheels are clearly visibly toeing in
20130617_163416_zps539b141a.jpg

There is some cambering
20130617_163359_zps59b05d6b.jpg

There is no more adjusting left on the steering rod ends
20130617_065956_zpsddb676db.jpg
20130617_163319_zpsc4108acb.jpg
20130617_163202_zpsf72e8af6.jpg

What can the alignment shop do that I'm not seeing right now? I thought negative caster was bad for driveability, but that seems to be the only way to get it done. And now at least I know for sure that the previous owner(s) where driving with a buttload of negative caster, since the wheel was pulled back at least a couple of cm's on the old short springs and shocks.

Could be they fitted the wrong tie rods somewhere in the past and decided to counter act that by giving it negative caster? As I understand some other series use the same thread just different lengths?
I don't think the subframe is out of position, since the bolts are exactly where they are supposed to be. Anyone know the standard length of a R33 track rod? I know the new ends are 15mm longer, but on the old setup (with the negative caster) that still gave me plenty thread to realign. On the right caster though i can never get it aligned. What I'm going to try today is lift the car up about a cm and pull the wheels a little more towards that 6 degrees. The caster right now isn't enough yet to pull the wheels straight again. When cornering now I really need to turn them straight myself, otherwise I'll end up on the side of the road.. I was thinking about adding some thread to the stock ones, even though there's not much left on the rod to put thread on and shortening them a couple of cm's.
Japspeed is now trying to get me to buy their track rods as well.. Which I didn't intent to.. Why sell rod ends if you end up needing the rods too??

My guess it that somebody fitted the wrong length tie rods and to compensate for length difference, they pushed back the caster.
What I did::
- Old tie rod / end measured how much thread was left.
- Removed old end
- Measured old and new ends (new one 15mm longer) which gave me approx 15mm free space on the thread.
- Replaced Struts / tension rods (about 10mm lower than before).
- Caster to just positive (should actually be around 6 degrees, but thats for the alignment shop, as long as it's not negative)
- Fitted the new ends and adjusted so that it compensated the length difference

- Toe-in... A lot..
- Tried adjusting the tie rods, but dead end.. And still toe-in..
If i now press the caster backwards, it actually decreases the toe-in and actually starts pulling the rear of the wheel inwards, but also makes the caster go negative.

Subframe is not moved or bent (deviation is identical on both sides and subframe is still neatly on the mounting bolts), and I can't find any bent rods or arms (would be a huge coincidence that both sides are equally crooked).
On soc they just state that I should have bought the tie rods as well, because it won't work with standard tie rods (why the hell to they sell just the ends without mentioning it then?).
I now have a few options. Buy the tie rods from japspeed and hope I can get them shorter, shorten the ones I have now and lengthen the thread on them, or shorten the new ends which then makes them a lot less reliable.

Does anyone happen to have a loose R33 tie rod, to measure the length from the rack to the end?

S14/R33 ones are 290mm

the issue here is the rods on the rack not the caster, people even run 10degress of caster ( say 6 more then "center" ...)

rack ends might be from another car or lock spacer, so too long and of course i'd assume that the rod ends are adjusted all the way, make sure the rubber boot isn't hiding some more thread on it

i think cefiro rack ends are m14 and are the same length as the s13 with is shorter so if all else fails give that a go

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It cost me $2900 all up for a local trailer / towbar place to supply and install. I did think it was a bit steep initially but after all the work involved and seeing the final result I think its well justified.  Hardest part was finding someone willing to customize and fit it up with trial and error basically. Whereabouts are you located? - I had my work done locally in Wangara.
    • Get something that can spray a bit, something like I'd use is a pressure pack for weed sprayer. I use one with degreaser. Spray it on (make sure you're fully covered up, you don't want that shit on you, especially face/eyes). Alternatively, a paint brush will help here as you can brush and work at the stuff quite aggressively.   Be aware, citric acid can eat metal away and will cause it to rust more later. So make sure you neutralise it when done, and give the fresh metal some protection. That hanger, I'd honestly bin and get something like the Frenchy's drop in replacement. The tank, again, I'd look for something else to replace it with. Remember, as metal turns to rust, it means there's less metal there now. So some patches of your fuel tank are likely to be quite thin.   Personally, Id focus on the front end of things, IE, how did the injectors get clogged if they're meant to be after a fuel filter. Then, once the front is sorted, I'd rig something up, even like a small surge tank, and make sure the engine is now running and all behaving. Then I'd replace the fuel tank and fuel hanger and pump. Also, I'd already be preparing to ditch your fuel filter...  
    • That's looking great! Are you planning to do things like all hidden wiring with it, or you're planning to have it look more like we'd expect an RB in an engine bay to look like?
    • Haha thanks everyone, I'll take everyone's suggestions into consideration. If I do eventually choose a car ill post it here update on the mods I do.
    • I found the ingredients at larger amounts from a Coffee Shop. 1kg Citric Acid for €8.50 500g Baking Soda for €2.50 I tried it out tonight distilled water (I got from my ACs) and dish soap. It does get bubbly with dish soap. In just two hours the hanger has improved significantly and rubbing against any remaining rust seems to flake it off. I'm going to leave it a little bit longer and see how it goes. I have read that someone even used this solution in an ultrasonic cleaner to clean a seized water pump which brought it back to life.
×
×
  • Create New...