Jump to content
SAU Community

Recommended Posts

My A31 (1993 SE-4) has always done this thing where once the car starts moving it fires the central locking and locks all the doors, except the drivers. It's always annoyed me a little bit but not enough to do anything about it.

Unfortunately this system seems to have developed a fault, if you attempt to unlock one of the doors it instantly locks it again. It appears that the door lock actuator is being fired continually which I imagine is going to wear them out sooner or later.

I'd like the keep the central locking working, but disable this one specific feature, is there any way to do that?

Link to comment
https://www.sau.com.au/forums/topic/428384-disabling-the-automatic-door-lock/
Share on other sites

sounds similar to what the new Hyundai's do where all the doors lock after 15km/h it's part of the safety and i believe it can be disabled at the service department.. not sure if that's of any help but i'd take it to someone that knows their way around a locking system.

Chris Rogers for instance.

It's a factory feature, it's not a fault & it's not constantly firing, the master unit for the central locking detects when the locks actuate and will try to lock them again.

They won't 'wear down' over time because of this.

If anything, trying to manually unlock the door while moving will wear our parts, hitting the button on the driver's door probably doesn't do much good either.

I know of one dude that ended up with a bent door lock actuator rod from a passenger trying to constantly override it.

Central locking is controlled by the passenger side power window switch (it's built in)

Other than removing your speedo, or removing your central locking and/or passenger's power window switch, I don't know of any way to remove it.

You could get someone else to drive, , unplug the passenger window switch and use a multimeter to look for a signal that comes on around 10kmp/h (often 15 or 20kmp/h with older/stretched speedo cables), theoretically there's a wire off the dash that triggers something inside that switch to lock all the doors.

Don't know if it's a simple as cutting one or two wires and if that'll cause other issues, but if you're that desperate to get rid of it, it's worth a shot.

Had a look but apparently my search abilities suck, not helped by the fact that all the results for "lock" are about steering, probably also not helped by my lack of knowing Australian English.

The reason this came about is my GF managed to get her hair trapped in the door and didn't notice until I was joining the motorway, when she unlocked the door the dam thing fought back hard enough that it bent her fingers back.

The car will only lock the passenger doors, not the drivers side....so, the safest place for your girlfriends hair is probably in your lap....just saying....

Why was her hair near the lock anyway? that's a mile away from the headrest.....

Windy day and her hair is waist length so easy to trap it when closing the door, hell I manage to shut my own hair in the door sometimes and mine's only armpit length. I usually notice before reaching a sufficient speed for the doors to auto lock.

As for your other suggestion, while it has appeal it would be somewhat easier if I were a bloke :P

Windy day and her hair is waist length so easy to trap it when closing the door, hell I manage to shut my own hair in the door sometimes and mine's only armpit length. I usually notice before reaching a sufficient speed for the doors to auto lock.

As for your other suggestion, while it has appeal it would be somewhat easier if I were a bloke :P

sounds like a fun relationship :P

seems my memory is abit off although have redeemed my self by finding said post

http://www.skylinesaustralia.com/forums/topic/100905-auto-door-lock/?hl=%2Bmike#entry6656673

Edited by Dan_J
  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...