Jump to content
SAU Community

Purchasing Diff Shims

Shelford93
 Share

Recommended Posts

  • 3 weeks later...
GTSBoy Grand Master

GTSBoy

Posted
Posted

The viscous LSD action occurs INSIDE the viscous cartridge. By jamming more shims into the space OUTSIDE the viscous cartridge, you are not in fact improving the LSD action of the diff. You are just creating a wear surface on surfaces that were not supposed to wear. As such, it is neither a smart thing to do, nor is it even anything more than a temporary act, seeing as the shim, cartridge and housing surfaces will all wear until the extra friction you have jammed in there has done its job.

It's job, by the way, is to create lots of very fine particles of cast iron and steel.

GTSBoy Grand Master

GTSBoy

Posted
Posted

Some R34s come with a helical. Until recently I was almost prepared to believe that they were mythical, having never, ever seen one. Then someone posted a picture of one on here, freshly shipped from Japan.

MOST of the R34s appear to have VLSD.

No, you cannot shim a helical diff. But that doesn't matter, because as an LSD they shit all over a VLSD, or a shimmed VLSD. The quality of the drive from a helical is outstanding. I have one in my R32 and wouldn't swap it for a mech diff (for street driving). I might be willing to consider a much more aggressive mechanical diff for a circuit car.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
×
×
  • Create New...