Jump to content
SAU Community

Recommended Posts

Hi I replaced my left front wheel bearing on my r32 4 door. I have the hub bolted back in but I am reluctant to put the wheel and brake assembly back on yet. This is because the hub is soo damn tight to turn! I can do it by hand but its take far more force than it should. Its not normal, at least I think its not :/

Cant feel anything binding or rubbing, just feels like there is too much preload on the bearings like if you crank the nut up too tight on a trailer hub.

I am a apprentice mechanic and I have done many of these bearings before with no issues.

Any ideas as to what might be wrong? Or is it fine? I am think perhaps the bearing preload is setup incorrectly when the bearing was manufactured.

Link to comment
https://www.sau.com.au/forums/topic/428929-wheel-bearing-help/
Share on other sites

You arent dont the right bearing as well? I was going to say do it and then see if you have the same issue then you will know its a bearing problem

On Nissan Fast it shows a washer at the back of the hub behind the nut then bearing - snap ring - seal - hub

Thats about all the help I can give, having never done wheel bearings on my car

Nah just the left one because it was noisy. Had corrosion in there because water got past the seal :( I think its been replaced before at some stage, car has over 400,000ks on it and to me it looks like someone put the wrong seal in! the old one looks like its the one thats meant to be on the back that seal on the cv joint on a AWD model. ( mines 2wd )

Yeah the washer is on there. Its just there to prevent he drive flange coming out and to stop it turning inside the bearing. Temped just to drive on it and see how it goes. Im thinking its the seal is squashed up against the bearing too hard ( for whatever reason, idk ). I dont want to pull it apart again as that can damage the bearing races because there is no way to disassemble it without pressing on them.

Kinda screwed either way really. I know it will loosen up over time but i would likely damage the bearing and I would be $120 out of pocket. And if its the seal causing the issue the seal would get damaged from rubbing, water and dirt would get in and again, damage the bearing.

Might have to play it by ear a guess.

Edited by Black4DR

FIXED!

Thanks for the input guys.

I was my mistake. I put the seal onto the flange and pressed the flange into the hub. You are suppose to tap the seal into the hub first then press the flange into the hub.

I just gave the seal a few love taps with a screw driver and hammer and now she it mint :) didn't take much at all, most of the seal pulled its self into the hub haha

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...