Jump to content
SAU Community

Various Gtr And Gtst Parts For Grabs

huli
 Share

Recommended Posts

huli Experienced

huli

Posted
Posted

Hey all,

Need to clear out some room from the shed and need these parts gone as I no longer need them. All parts were removed in working order and were replaced only by new parts for the new set up of the cars. The list is below and will add photos later but you can PM me on here or sms me on 0400262578 for pics. Will try to upload pics as soon as possible.

33 GTSt Stuff

1. rear stock lower control arms $80 the pair

2. rear stock camber arms $40 the pair

3. rear stock traction rods $40 the pair

4. HICAS 4 wheel steering unit + tie rods $100

5. complete front and rear calipers and rotors only (no hubs or knuckles) $300

6. Diff centre minus ring gear $200

7. a/c condenser unit and all under bonnet lines to firewall $100

8. washer bottle and both motors $30

9. TRUST pod filter with green label air flow meter $80

10. clutchless fan $30

11. BLITZ blow off valve (rare) $100

12. turbo induction piping $10 each

13. fuel tank and fuel pump assay $150

14. cat back exhaust and kakimoto cannon (mild steel) $100

15. front castor rods $100 the pair

16. front LCA's $100 the pair

17. front camber arms $40 the pair

18. front traction rods $40 the pair

19. RB25 gears set and selectors + main shafts $400

20. generic 12' thermo fan $80

33 GTR stuff

1. crank scraper (2 piece) $40

2. rear main crank seal $20

3. power steering pump bracket $20

4. stock water pump (no cavitation) $30

5. exhaust manifolds with heat shields $40 the pair

6. oil and water turbo lines $5 each

7. various water and vac lines $5-$15

8. air ballast chamber $30

9. O2 sensors $5 each

10. stock valve springs and retainers $100

Any more stuff I find in my travels I will add at a later date!

Cheers HULI

huli Experienced

huli

Posted
  • Author
Posted

also have an air regulator for RB26

(the bit that sits under the intake plenum)

Also have the centre grille for a S1 GTSt

(mint condition and in 2PAK silver)

cuong nguyen Proficient

cuong nguyen

Posted
Posted

7. a/c condenser unit and all under bonnet lines to firewall $100


8. washer bottle and both motors $30



how much to post this to canberra? does the air con stuff come with the compressor?

huli Experienced

huli

Posted
  • Author
Posted

For all those people asking the front rotors measure 29.5mm in width and the rears measure 19mm in width. these come with the front and rear disk callipers and brake pads. so slap it on and go!!!!

huli Experienced

huli

Posted
  • Author
Posted

Still got the O2 sensors and in very good condition!

If anyone needs better photos or something let me know and I can put them up on here or msg me and I'll send you a MMS. My number is 0400262578

Cheers HULI

PS would rather have pick up for exhaust system.

Also if you need some parts and not others I am willing to separate if need be!

huli Experienced

huli

Posted
  • Author
Posted

If you want quality used stock parts and don't like the price, then shoot me a pm or msg with your offer and we'll go from there. All postage paid by buyer tho!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      V37 Suspension change

      By Duncan · Posted

      You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      OK, so a bunch of trim needs to come off to get to the rear shock top mounts. Once the seat is out of the way, the plastic trim needs to come off. Remove 2 clips at the top then slide the trim towards the centre of the car to clear the lower clip Next you need to be able to lift the parcel shelf, which means you need to remove the mid dark trim around the door, and then the upper light trim above the parcel shelf. The mid trim has a clip in the middle to remove first, then lift the lowest trim off the top of the mid trim (unclips). At the top there is a hidden clip on the inner side to release first by pulling inwards, then the main clip releases by pulling the top towards the front of the car. The door seal comes off with the trim, just put them aside. The the lighter upper trim, this is easy to break to top clips so take it carefully. There is a hidden clip towards the bottom and another in the middle to release first by pulling inwards. Once they are out, there are 3 clips along the rear windscreen side of the panel that are hard to get under. This is what the rear of the panel looks like to assist:
    • GTSBoy
      R34 manual conversion speed signal wire finding, need help

      By GTSBoy · Posted

      Yes. Autos typically work from the speed sensor on the pinion shaft of the diff. I also think that even if you have a proper speed sensor for the bog manual in the manual box, that the signal it outputs is not compatible with the auto dash anyway. You should consult that manual (the book, not the gearbox).
    • GTSBoy
      First time Skyline owner

      By GTSBoy · Posted

      And I just realised that that advice is slightly nonsensical for a GTR, because you need 2 of them. But it is otherwise true.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Having had a reasonable look at the car, I'll be able to remove the (one time) rams and retract the hinge (they are held in the down location by a tiny (m3?) sacrificial screw) which will get it physically back in shape. From there if you remove the rams you need a resistor to turn off the airbag light (as Mark said, there are plug in kits and I might go that way because its reversible). And...per all the threads on here, even if you have the resistors to turn off the airbag light, the bonnet light will stay on as it writes to the airbag computer history - that is either replace the airbag controller, reprogam the EPROM (if I can work out how), or remove the globe from the dash. Having seen how sensitive this system is, if I had my time over I'd pre-emptively remove the rams, even on a road car, because this is all a very unnecessary pain in the arse. Reminds me, time to go and have a look at the Fuga too....
×
×
  • Create New...