Jump to content
SAU Community

Recommended Posts

Bryce it's only used for sealing the actual butterfly inside the throttle body.

IF you haven't cleaned the stock stuff off then you have nothing to worry about.

You would think the workshops around here would have something they use.

I texted my mate at Toyota and he is going to check for me.

If I can't find anything then I might just bite the bullet and order some of the stuff.

Check this stuff out guys

http://www.permatex.com/products/product-categories/gasketing/gasket-sealants/permatex-form-a-gasket-no-2-sealant-detail

"Slow-drying, non-hardening brush-top sealant approved for use in aviation as well as automotive applications. Temperature range -65°F to 400°F (-54°C to 204°C); resists gasoline, oil and grease. - See more at: http://www.permatex.com/products/product-categories/gasketing/gasket-sealants/permatex-form-a-gasket-no-2-sealant"

Suggested Applications: Valve cover gaskets, oil pan gaskets

kasko you should try some Hylomar, was recommended to me by scotty for sealing off my plenum and its worked so far, so for your throttle body it would be worth the $14 to try.. comes in a bottle or spray

Started up the car on Monday and it had a rough idle.

Gave it a little rev and it stalled.

Been trying to diagnose the issue for the past 2 nights.

After checking fuel & spark I finally got to checking comp

GAME OVER

Cyl 1 = 90

Cyl 2 = 25

Cyl 3 = 70

Cyl 4 = 90

Cyl 5 = 60

Cyl 6 = 70

Haven't done it at all

Owned the car for 45,000km

And I'm not sure when the previous guy did it.

I guess I should have checked it and done it when I first purchased the car. As you know I have had both power steering and fan belt snap.

Yep i recall :P

Maybe check the timing and condition on it first by just taking the top cover off....

The fact all cylinders are down indicates something dodgy going on...

Everyone seems to think the engine could still possibly be okay. I always fear the worst in these situations.

I'll take the cover off tonight if its easy enough to get to. Should only be a few bolts right?

Yeah its easy enough man!

And at the end of the day, who cares if its the engine? Its a standard RB, its not the end of the world :) Look at the positives hehe

Yeah its easy enough man!

And at the end of the day, who cares if its the engine? Its a standard RB, its not the end of the world :) Look at the positives hehe

Not worried about the cost of a new engine.

More worried about the labour costs to pull out and fit a new engine.

Not worried about the cost of a new engine.

More worried about the labour costs to pull out and fit a new engine.

You have mates local, beers + Sausage fest and itll get done!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Cheers. Skyline is back on the menu, can’t get rid of it. It’s like a child you don’t want, or herpes 
    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
×
×
  • Create New...