Jump to content
SAU Community

Recommended Posts

Wrecking r33 gtst manual series 1.5

111000kms

I'm located on the Gold Coast

Rb25det s2 engine complete

Genuine 111000kms

$1150

R33 gtst full manual conversion

Gearbox has been recoed at some stage

1350

R33 series 1 headlights

Mint condition all mounts intact

$200 pair

R33 s1 type m front bar

$130

R33 type m side skirts

$70

R33 type m rear pods

$50

R33 S1 headlights

Few broken mounts not best of condition

$50 pair

R33 gtst complete rear subframe includes everything

$300

R33 stainless catback exhaust 3 inch

$120

R33 series 1 bonnet with n1 type lip

$100

R33 gtst front brakes and rotors

$200

R33 bm44 non abs bmc

$40

Starcorp 17 inch wheels

With near new tyres

$500

R33 12 pin drivers window switch

$60

R33 drivers window motor and reg

$50

R33 passenger window motor and reg

$20

Greddy turbo timer

$30

R33 s2 dash cluster manual

$60

R33 s1 and 2 dash great condition

$40

Rb25 engine covers with timing cover

$80

Custom alloy intake pipe with afm for rb25 get rid of the rubber one

$90 will separate

R33 complete interior everything

$90

R33 king springs full set

$90

R33 s1 manual ecu

$50

Turbosmart boost tee

$20

Rb25det head complete with covers intake etc no turbo or cas

$180

R33 engine mounts

$40 pair

R33 engine brackets

$30

R33 engine crossmember

$50

R33 steering rack

$30

R33 s2 steering wheel great condition red stitching

$60

Front lower control arms

80 pair

Have heaps more probs missed heaps

Gold Coast

Except PayPal but you will have to pay fees

0487924497

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Lets say I wanted to buy this, specifically for this purpose. How do I actually perform the function. Can I still buy a Consult-1? Am I about to be burned by the fact my car is a 2000 model Series 2 R34 and thus will be some stupid other system? Do I just need this -> https://obd2australia.com.au/product/nissan-consult-14-pin-to-usb-ddl-diagnostic-interface-with-ftdi-ft232r-chip/ And with what software?
    • That's probably OK. That's a face to face compression joint between two surfaces with the clamping load provided by those bolts. So.... it's unlikely that the bolts will end up feeling that load in shear, unless the clamping surfaces are not large enough, bolts not got enough tension on them, etc etc to prevent the two faces from moving wrt each other. Which... I would hope the designers have considered, seeing as it's probably one of the most important things the upright has to do apart from resist collapsing in its own right. But yes, it would definitely be worth asking them what their safety factor on that part of the design was. I tend to think that the casting, being a casting, is not necessarily the strongest bit of material in the world. It's about an inch square, and when you think about the loads that are being put into it, you have to wonder what safety factor the Nissan boys (and every other OEM engineer who has designed all the millions of other uprights that look essentially the same) used to account for defective casting, aging, severe impacts on the wheel, etc etc. 
    • Those bolts would be orders of magnitude stronger that cast aluminium though.  And its mainly clamping force, not shear they are dealing with?
    • Except all that twisting force that is breaking a cast piece, appears to be going through 4 bolts in the picture Johnny posted of the BryPar one...
    • The smart approach is to use the gearbox loom from the manual car. Makes it a lot easier - just plugs into the switches on the box and plugs into the main loom up near the fusebox. Then you only need to deal with bypassing the inhibit switch. The other approach requires you to use the wiring diagram to identify those wires by colour and location, perhaps even indulging in a little multimeter action to trace them end to end to make sure, and then.... you will have the answers you need. The R34 wiring diagram is available on-line (no, I do not have a link to it myself - I would have to do a search if I wasn't able to go to the copy I have at home).
×
×
  • Create New...