Jump to content
SAU Community

Recommended Posts

^^^^^ this is correct providing you don't have a runner spacer.

Just an FYI.....you will find that Dales Brace bar will probably make a bigger and more noticeable improvement.

i have upper and dales lower. Top might aswell be for decoration as it does SFA compared to the lower.

Also easy as to put in and dale....bit odd but good bloke hahah :-P

Link to comment
https://www.sau.com.au/forums/topic/431139-m35-strut-brace/#findComment-6998749
Share on other sites

Pretty sure bigkevracer got the ox motorsport bracing off streeter for the m35

Sorry haven't got on here much lately. I've got Dale's front brace, the OX rear that Jetwreck organised in the group buy, and a Freeway Dolphin strut brace that Streeter organised.

These days I think the strut brace serves more use as a place to cable tie hoses to, but I've left it in. Looks purdy, and makes some difference, but with Dale's brace and all the bushes replaced, front end is pretty direct without it.

Link to comment
https://www.sau.com.au/forums/topic/431139-m35-strut-brace/#findComment-7003132
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi. This is just my curiosity because iam sure the tuner figure something out...but either way i want to ask. The "problem" is that the Nistune ECU (Stagea FW and RB25DET NEO from Stagea) sees many times the speed than the speedo does(he says the speedo show 120 km/h - correct speed and the ECU shows like 510km/h ) I told him that this car/tranny getting speed from rear diff. If iam not mistaken the RB25DET NEO "need" to see tranny speed sensor? (my tranny has the plug for it). So couple of "question" If he connects/wire the speed sensor to the tranny...are the signals gonna intervene and if...what if he disconnects the rear diff one and the speedo stops working? Or the "new" sensor from the tranny "take over" and will not going need the one from diff? As i said i know he figure/get that done...iam just curious to know what are the solutions 🙂 
    • Your IACV is set to idle too low. You need to adjust it via the screw Duncan mentioned. From memory it should be 650rpm with the valve electrics unplugged. What is it trying to idle at with the IACV plugged in?
    • Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
×
×
  • Create New...