Jump to content
SAU Community

Mugabetown - Whoretownin' At It's Worst.


Recommended Posts

Nick, Ben did a [email protected] at Jambo in an RB26 powered R32 GT-R. What's your dirty old pushrod motor got now?

Fastest LS1 in Australia is 6.8, jus sayin.

Of course I have no idea who ben is or what class it ran in!

Edited by Bunta

I said 'your,' meaning Nick's motor.

phew! Thank gawd for semantics :P

Fair enough, in that case compare him to a stock R32 GTR...which is still a good half second faster down the 1/4 :P

Fair enough, in that case compare him to a stock R32 GTR...which is still a good half second faster down the 1/4 :P

Which explains why Chris's v spec was in the high 14 and toms 33 with n1s on it ran identical times to mine.

Yes they can do a 13.0 but nobody will do it cause u might get 3 runs untill u shit something

Fair enough, in that case compare him to a stock R32 GTR...which is still a good half second faster down the 1/4 :P

This is true. I was also alluding to his allegations of RBs being hopeless.

But then you caught out my implied insult to the LS1 :(

Which explains why Chris's v spec was in the high 14 and toms 33 with n1s on it ran identical times to mine.

Yes they can do a 13.0 but nobody will do it cause u might get 3 runs untill u shit something

I have seen with my own 2 eyes a stock one do a 13.2 something and one with a decent clutch and a ECU do well into the 12s.

Those times are....not good. And knowing Chris in particular the launch would have been a softie.

This is true. I was also alluding to his allegations of RBs being hopeless.

But then you caught out my implied insult to the LS1 :(

They could do a 6 second pass, won't change the fact that I broke 2 of them and think they're weak as piss droney horrible sounding boost fed midget motors

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...