Jump to content
SAU Community

Mugabetown - Whoretownin' At It's Worst.


Recommended Posts

Yes a special tool was cobbled together out of 3 x 1/4" extensions and a knuckle joint etc etc to narrowly avoid everything in the bay and latch onto the 14mm bolt, smashed it out in minutes.

Nope not in comp with Labdirect, so busy with my 'real' job that I don't have time to look at anything else at the moment :(

Today is a good day for a drive, methinks

Pete I would say radiator out, fan and clutch off, belts off, covers off, get it on top dead center, crack all the cam gear bolts before you losen the tensioner on the belt, mark edge of belt and gears with white out or paint pen, losten tensioner, slip belt off, carefully remove gears without turning cams, transfer marks from old gears to new ones, put back togeather the belt, turn the engine over by the crank bolt about 6-8 revolutions and then line the timing marks up again off the pulleys and block( the belt will be in a different spot)

If they all line up back togeather undo the tensioner and then retighten so it is seated right

Once tight, tighten cam pulley bolts and put it back togeather

While your in there I would recommend getting a timing belt kit, do the pulley's and seals same time

And also while you you are that far in you should probably do water pump

Pm me if you want and I can give you a full rundown but more descriptive

Pete I would say radiator out, fan and clutch off, belts off, covers off, get it on top dead center, crack all the cam gear bolts before you losen the tensioner on the belt, mark edge of belt and gears with white out or paint pen, losten tensioner, slip belt off, carefully remove gears without turning cams, transfer marks from old gears to new ones, put back togeather the belt, turn the engine over by the crank bolt about 6-8 revolutions and then line the timing marks up again off the pulleys and block( the belt will be in a different spot)

If they all line up back togeather undo the tensioner and then retighten so it is seated right

Once tight, tighten cam pulley bolts and put it back togeather

While your in there I would recommend getting a timing belt kit, do the pulley's and seals same time

And also while you you are that far in you should probably do water pump

Pm me if you want and I can give you a full rundown but more descriptive

or just give it to Zac to do :)

or just give it to Zac to do :)

Yeah but that costs lots of cash moneys

I can get a quote for Pete and let him know on Monday

Also Zac.........attachicon.gifImageUploadedBySAU Community1392450026.288363.jpgclutch fan and cooling fan is back in its place all shiny and stuff ;)

This makes Zac happy :)

Glad I could help

Pete I would say radiator out, fan and clutch off, belts off, covers off, get it on top dead center, crack all the cam gear bolts before you losen the tensioner on the belt, mark edge of belt and gears with white out or paint pen, losten tensioner, slip belt off, carefully remove gears without turning cams, transfer marks from old gears to new ones, put back togeather the belt, turn the engine over by the crank bolt about 6-8 revolutions and then line the timing marks up again off the pulleys and block( the belt will be in a different spot)

If they all line up back togeather undo the tensioner and then retighten so it is seated right

Once tight, tighten cam pulley bolts and put it back togeather

While your in there I would recommend getting a timing belt kit, do the pulley's and seals same time

And also while you you are that far in you should probably do water pump

Pm me if you want and I can give you a full rundown but more descriptive

Yeah, i've been digging through guides, process itself is pretty straight forward. Thanks for the tip of smashing off the cam gear belts before removing the tensioner, hadn't thought of that one.

Timing belt and pulley's have been done recently, unless the tensioner/water pump etc is obviously stuffed i probably won't bother replacing them, either way once i tear it down i can make a decision and get the parts before i put it back together again.

Then.. fuel pump, injectors and AFM.

Then getting the car to the workshop. I'm figuring flatbed may be the best bet, anyone know a good towing mob?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Have a vb in honour of the car comming back
    • It was a great, but typical track day, and some VB was ingested at the night time debrief 🤪
    • And so, to round this out, I couldn't be happier to confirm @MBS206 has decided to buy the car. He drove down from sunny QLD with a trailer last week and it is off to its new home today. I'll let Matt confirm on next steps but I understand broadly that the plan is to leave it pretty much as is, and just get some quality wheel time with a nicely balanced car that is pretty much track ready. There are a few a jobs still to be done first but nothing too major and I think its a very smart buy Dinner last night at the Paragon with a round of VBs (mostly) for Neil
    • Well, 50 pages and the end of a chapter for this car. We took it out for a shakedown at Wakie yesterday, and everything went well. There were a couple of niggles: - Oil cooler fitting leak - tightened, cleaned, stopped leaking - Radiator cap overflow fitting was leaking....Mark called it, the overflow fitting was threaded in and not tight....tightened, tested and held pressure - Small oil leak at the rear of the block, probably the turbo oil feed - too hot to get at it comfortably but probably just needs to be nipped up - leak at the driver's side rear brake line where it meets the hardline. Fitting wasn't loose, so Matt backed it off and back on, no further leaks - there's also a leak somewhere on the top of the fuel tank, maybe that cross over fuel line - that was has been left to fix when its on a hoist Otherwise than those niggles the car went great, turned great and stopped great so it was a very successful day out. I'm always really nervous when a car first hits the track after a long break, especially with a brand new engine as well but it was great. VID-20251011-WA0007.mp4  Big thanks to @The Bogan who dropped by and helped out, @MBS206 and my nephew Lachlan the apprentice.  Neil's wife Mel also surprised the hell out of all of us by dropping by; she's up in Tamworth these days but was travelling to Melbourne so had plausible deniability for turning up at the garage, it was great to see her but also obviously a bit sad all round.
    • Skyline R33 Series 2 sedan tail lights in excellent condition. These are becoming harder to find, especially in this state.    BOTH SETS ARE IN FANTASTIC CONDITION (REFER TO PHOTOS)    ✅ No broken covers or cracks ✅ Lenses are in flawless condition ✅ All rear mounting lugs intact ✅ Comes complete as pictured ✅ Perfect for restoration, replacement, or upgrade   These lights are ready to go, no surprises just quality OEM parts.   These are definitely one of the better sets we have seen in a while. With minimal wear and tear they will come as you see. Bear in mind they are not brand new they are almost 30 years old now. To find them in this condition isn’t easy they can only be obtained on the second hand market.   Australia Wide Postage Available At Buyers Expense. Silver Set:$850 Grey Set:$850 PM Me for purchase or any other questions  IMG_2166.dng IMG_2165.dng IMG_2172.dng IMG_2173.dng IMG_2174.dng IMG_2179.dng IMG_2180.dng IMG_2260.dng IMG_2258.dng IMG_2259.dng IMG_2261.dng IMG_2266.dng IMG_2273.dng IMG_2274.dng IMG_2276.dng
×
×
  • Create New...