Jump to content
SAU Community

Mugabetown - Whoretownin' At It's Worst.


Recommended Posts

Yes a special tool was cobbled together out of 3 x 1/4" extensions and a knuckle joint etc etc to narrowly avoid everything in the bay and latch onto the 14mm bolt, smashed it out in minutes.

Nope not in comp with Labdirect, so busy with my 'real' job that I don't have time to look at anything else at the moment :(

Today is a good day for a drive, methinks

Pete I would say radiator out, fan and clutch off, belts off, covers off, get it on top dead center, crack all the cam gear bolts before you losen the tensioner on the belt, mark edge of belt and gears with white out or paint pen, losten tensioner, slip belt off, carefully remove gears without turning cams, transfer marks from old gears to new ones, put back togeather the belt, turn the engine over by the crank bolt about 6-8 revolutions and then line the timing marks up again off the pulleys and block( the belt will be in a different spot)

If they all line up back togeather undo the tensioner and then retighten so it is seated right

Once tight, tighten cam pulley bolts and put it back togeather

While your in there I would recommend getting a timing belt kit, do the pulley's and seals same time

And also while you you are that far in you should probably do water pump

Pm me if you want and I can give you a full rundown but more descriptive

Pete I would say radiator out, fan and clutch off, belts off, covers off, get it on top dead center, crack all the cam gear bolts before you losen the tensioner on the belt, mark edge of belt and gears with white out or paint pen, losten tensioner, slip belt off, carefully remove gears without turning cams, transfer marks from old gears to new ones, put back togeather the belt, turn the engine over by the crank bolt about 6-8 revolutions and then line the timing marks up again off the pulleys and block( the belt will be in a different spot)

If they all line up back togeather undo the tensioner and then retighten so it is seated right

Once tight, tighten cam pulley bolts and put it back togeather

While your in there I would recommend getting a timing belt kit, do the pulley's and seals same time

And also while you you are that far in you should probably do water pump

Pm me if you want and I can give you a full rundown but more descriptive

or just give it to Zac to do :)

or just give it to Zac to do :)

Yeah but that costs lots of cash moneys

I can get a quote for Pete and let him know on Monday

Also Zac.........attachicon.gifImageUploadedBySAU Community1392450026.288363.jpgclutch fan and cooling fan is back in its place all shiny and stuff ;)

This makes Zac happy :)

Glad I could help

Pete I would say radiator out, fan and clutch off, belts off, covers off, get it on top dead center, crack all the cam gear bolts before you losen the tensioner on the belt, mark edge of belt and gears with white out or paint pen, losten tensioner, slip belt off, carefully remove gears without turning cams, transfer marks from old gears to new ones, put back togeather the belt, turn the engine over by the crank bolt about 6-8 revolutions and then line the timing marks up again off the pulleys and block( the belt will be in a different spot)

If they all line up back togeather undo the tensioner and then retighten so it is seated right

Once tight, tighten cam pulley bolts and put it back togeather

While your in there I would recommend getting a timing belt kit, do the pulley's and seals same time

And also while you you are that far in you should probably do water pump

Pm me if you want and I can give you a full rundown but more descriptive

Yeah, i've been digging through guides, process itself is pretty straight forward. Thanks for the tip of smashing off the cam gear belts before removing the tensioner, hadn't thought of that one.

Timing belt and pulley's have been done recently, unless the tensioner/water pump etc is obviously stuffed i probably won't bother replacing them, either way once i tear it down i can make a decision and get the parts before i put it back together again.

Then.. fuel pump, injectors and AFM.

Then getting the car to the workshop. I'm figuring flatbed may be the best bet, anyone know a good towing mob?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Its also worth mentioning that 30 years after it left the factory and god knows how many missed oil changes since, there is every possibility that one or more lifters are ticking because they are sticky/gummed up. To resolve that you need to pull the cams then pull each lifter, disassemble, clean, reassemble, soak in oil and re-install, and they should come up good as new.
    • What air filter are you running? Is it a panel filter in the stock air box, or a pod filter? Is the air filter the type that is oiled?   If you unplug the IACV, what rpm does the engine idle at?
    • Reading through the engine service manual their advice is do a cylinder balance test. Unplug one injector at a time and see if the idle drops a consistent RPM. You can also do this using a Consult cable which is easier. They also call for unplugging the power transistor, then with the engine off and the fuel rail unhooked from the manifold verifying that you have good fuel flow (even injection, no dripping/leaks, etc) when you twist the CAS by hand. Also verify the spark by pulling the spark plugs and allowing the plugs to ground and turning the CAS by hand. I would also start doing the sensor checks and idle valve checks in service manual. Make sure the MAF tests reasonably, the intake air regulator is sane, etc. You may have to get new spark plugs.
    • This sounds very old of me, however since buying the Tiguan shit box, my view on shit boxes have changed.
    • I've looked up the parts number (41011AL501). It's around $700 OEM. Usually our Infiniti G35 here in Canada have interchangeable parts with my Stagea but the parts number are not the same. I have looked around and it seems the JDM 2005 V35 Skyline (which is the same as our G35) has the same caliper but I cannot confirm. And I can't find a repair kit. The inner brake pads drags on the rotor, seems to be rusty piston. Thanks for the info by the way
×
×
  • Create New...