Jump to content
SAU Community

Mugabetown - Whoretownin' At It's Worst.


Recommended Posts

Yes a special tool was cobbled together out of 3 x 1/4" extensions and a knuckle joint etc etc to narrowly avoid everything in the bay and latch onto the 14mm bolt, smashed it out in minutes.

Nope not in comp with Labdirect, so busy with my 'real' job that I don't have time to look at anything else at the moment :(

Today is a good day for a drive, methinks

Pete I would say radiator out, fan and clutch off, belts off, covers off, get it on top dead center, crack all the cam gear bolts before you losen the tensioner on the belt, mark edge of belt and gears with white out or paint pen, losten tensioner, slip belt off, carefully remove gears without turning cams, transfer marks from old gears to new ones, put back togeather the belt, turn the engine over by the crank bolt about 6-8 revolutions and then line the timing marks up again off the pulleys and block( the belt will be in a different spot)

If they all line up back togeather undo the tensioner and then retighten so it is seated right

Once tight, tighten cam pulley bolts and put it back togeather

While your in there I would recommend getting a timing belt kit, do the pulley's and seals same time

And also while you you are that far in you should probably do water pump

Pm me if you want and I can give you a full rundown but more descriptive

Pete I would say radiator out, fan and clutch off, belts off, covers off, get it on top dead center, crack all the cam gear bolts before you losen the tensioner on the belt, mark edge of belt and gears with white out or paint pen, losten tensioner, slip belt off, carefully remove gears without turning cams, transfer marks from old gears to new ones, put back togeather the belt, turn the engine over by the crank bolt about 6-8 revolutions and then line the timing marks up again off the pulleys and block( the belt will be in a different spot)

If they all line up back togeather undo the tensioner and then retighten so it is seated right

Once tight, tighten cam pulley bolts and put it back togeather

While your in there I would recommend getting a timing belt kit, do the pulley's and seals same time

And also while you you are that far in you should probably do water pump

Pm me if you want and I can give you a full rundown but more descriptive

or just give it to Zac to do :)

or just give it to Zac to do :)

Yeah but that costs lots of cash moneys

I can get a quote for Pete and let him know on Monday

Also Zac.........attachicon.gifImageUploadedBySAU Community1392450026.288363.jpgclutch fan and cooling fan is back in its place all shiny and stuff ;)

This makes Zac happy :)

Glad I could help

Pete I would say radiator out, fan and clutch off, belts off, covers off, get it on top dead center, crack all the cam gear bolts before you losen the tensioner on the belt, mark edge of belt and gears with white out or paint pen, losten tensioner, slip belt off, carefully remove gears without turning cams, transfer marks from old gears to new ones, put back togeather the belt, turn the engine over by the crank bolt about 6-8 revolutions and then line the timing marks up again off the pulleys and block( the belt will be in a different spot)

If they all line up back togeather undo the tensioner and then retighten so it is seated right

Once tight, tighten cam pulley bolts and put it back togeather

While your in there I would recommend getting a timing belt kit, do the pulley's and seals same time

And also while you you are that far in you should probably do water pump

Pm me if you want and I can give you a full rundown but more descriptive

Yeah, i've been digging through guides, process itself is pretty straight forward. Thanks for the tip of smashing off the cam gear belts before removing the tensioner, hadn't thought of that one.

Timing belt and pulley's have been done recently, unless the tensioner/water pump etc is obviously stuffed i probably won't bother replacing them, either way once i tear it down i can make a decision and get the parts before i put it back together again.

Then.. fuel pump, injectors and AFM.

Then getting the car to the workshop. I'm figuring flatbed may be the best bet, anyone know a good towing mob?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • I see those two Stageas have the "punched 40mm hole" deregistered Japanese number plates 👍 Nice kouki group shot with the different colours too. 
    • Ended up just being a loose exhaust bolt luckily.
    • Yeah I made that post way too early, sorry I must have assumed it was bad because it's a 20+ year old thrashed shitbox lol. It was just a loose exhaust bolt. 
    • Like others have said, drop the power to give your drivetrain a % of reliability until you can up the drivetrain reliability  It isn't rocket science, build power to the weakest link with a % of safety Whilst upping the the reliability of the drive train is costly, there's no point in having the engine make big power if it keeps eating the drivetrain....ask me how I know, I had the tow truck on speed dial for a few years, and I spent huge amounts of money fixing issues and breakages that really would have been cheaper in the long run if I did it right the first time Me, I like a nice sized fudge factor, that keeps me off the tow truck
    • I don't understand what the issue is with, turn the boost down and start saving $$.  As soon as you can afford the supporting mods, turn the boost back up.  If the car is running fine, enjoy it. Turning the boost down isn't going to kill you. 
×
×
  • Create New...