Jump to content
SAU Community

Mugabetown - Whoretownin' At It's Worst.


Recommended Posts

Yes a special tool was cobbled together out of 3 x 1/4" extensions and a knuckle joint etc etc to narrowly avoid everything in the bay and latch onto the 14mm bolt, smashed it out in minutes.

Nope not in comp with Labdirect, so busy with my 'real' job that I don't have time to look at anything else at the moment :(

Today is a good day for a drive, methinks

Pete I would say radiator out, fan and clutch off, belts off, covers off, get it on top dead center, crack all the cam gear bolts before you losen the tensioner on the belt, mark edge of belt and gears with white out or paint pen, losten tensioner, slip belt off, carefully remove gears without turning cams, transfer marks from old gears to new ones, put back togeather the belt, turn the engine over by the crank bolt about 6-8 revolutions and then line the timing marks up again off the pulleys and block( the belt will be in a different spot)

If they all line up back togeather undo the tensioner and then retighten so it is seated right

Once tight, tighten cam pulley bolts and put it back togeather

While your in there I would recommend getting a timing belt kit, do the pulley's and seals same time

And also while you you are that far in you should probably do water pump

Pm me if you want and I can give you a full rundown but more descriptive

Pete I would say radiator out, fan and clutch off, belts off, covers off, get it on top dead center, crack all the cam gear bolts before you losen the tensioner on the belt, mark edge of belt and gears with white out or paint pen, losten tensioner, slip belt off, carefully remove gears without turning cams, transfer marks from old gears to new ones, put back togeather the belt, turn the engine over by the crank bolt about 6-8 revolutions and then line the timing marks up again off the pulleys and block( the belt will be in a different spot)

If they all line up back togeather undo the tensioner and then retighten so it is seated right

Once tight, tighten cam pulley bolts and put it back togeather

While your in there I would recommend getting a timing belt kit, do the pulley's and seals same time

And also while you you are that far in you should probably do water pump

Pm me if you want and I can give you a full rundown but more descriptive

or just give it to Zac to do :)

or just give it to Zac to do :)

Yeah but that costs lots of cash moneys

I can get a quote for Pete and let him know on Monday

Also Zac.........attachicon.gifImageUploadedBySAU Community1392450026.288363.jpgclutch fan and cooling fan is back in its place all shiny and stuff ;)

This makes Zac happy :)

Glad I could help

Pete I would say radiator out, fan and clutch off, belts off, covers off, get it on top dead center, crack all the cam gear bolts before you losen the tensioner on the belt, mark edge of belt and gears with white out or paint pen, losten tensioner, slip belt off, carefully remove gears without turning cams, transfer marks from old gears to new ones, put back togeather the belt, turn the engine over by the crank bolt about 6-8 revolutions and then line the timing marks up again off the pulleys and block( the belt will be in a different spot)

If they all line up back togeather undo the tensioner and then retighten so it is seated right

Once tight, tighten cam pulley bolts and put it back togeather

While your in there I would recommend getting a timing belt kit, do the pulley's and seals same time

And also while you you are that far in you should probably do water pump

Pm me if you want and I can give you a full rundown but more descriptive

Yeah, i've been digging through guides, process itself is pretty straight forward. Thanks for the tip of smashing off the cam gear belts before removing the tensioner, hadn't thought of that one.

Timing belt and pulley's have been done recently, unless the tensioner/water pump etc is obviously stuffed i probably won't bother replacing them, either way once i tear it down i can make a decision and get the parts before i put it back together again.

Then.. fuel pump, injectors and AFM.

Then getting the car to the workshop. I'm figuring flatbed may be the best bet, anyone know a good towing mob?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Jax Tyres this Monday morning. Front lifted 15mm Back lifted 12mm Quote1, $175 per tyre + wheel alignment. Quote2, $660 inc wheel alignment. paid $298 for the lot.  
    • Finally have an update on this  Rack came in this week so I did a test fit. You do need the S chassis bushings since the rack is 5mm thinner than the R33 rack. The main issue I foresaw and ran into was one of the hardlines not lining up properly with there it's meant to on the rack. After some gentle coercing and bending very slightly, I managed to get it to fit without any kinks and keeping the hardline pretty much in all of the factory mounting positions. I did have to unbolt all of the soft mounts to move the line around so I could snake it out and bend it safely but it looks good to me for now. I'll update when the rack is fully bolted in and functioning.  
    • I hear this thread needs an update following its adventures last Wednesday!
    • What are you thinking makes a sequential shit to drive on the street? About the ONLY thing I can think of, is if you're wanting to be able to roll up to lights in third or second and pop it straight into neutral, or you want to come down two or three gears, say out of 5th and back to second, but they shift quick enough it doesn't really matter
    • I'm not a drag racing guy, but that was a good watch. Didn't Ibrahim's car have some cooch! But the big question is....WTF is with so many of them running without seatbelts!
×
×
  • Create New...