Jump to content
SAU Community

Mugabetown - Whoretownin' At It's Worst.


Recommended Posts

Does remind me tho, I really need to fit an oil filter relocation kit to my car, it's too easy for someone to just reach under the car and steal...

I need to do this next happy laps...

  • Like 1

Aww yeah. Legit one too. Needs a set of wheels and it has a few issues around the place. but has a lot of goodies

Trust sump extension
R33 GTR crank
HKS oil pump
ACL race bearings
ARP main & head studs
Eagle H-beam forged conrods
CP forged pistions 86.5mm
Ross metal jacket harmonic balancer
Tomei metal head gasket (oil restrictor fitted)
Tomei adjustable cam gears
Gates timing belt
Splitfire coilpacks
Nismo adjustable fuel pressure regulator
Nismo high flow fuel pump
Nismo low temp thermostat
Apexi power FC version 8.04a with hand controller
Garret GT2860R -7 turbos
HKS extension kit
HKS oil cooler & filter relocation kit
K&N reusable panel filter
Custom stainless exhaust 3" front pipes into 2.5"
DBA 4000 series rotors
EBC greenstuff pads up front, bendix ultimate rear
HSD HR coilovers
Billet aluminium rear subframe bushes
Adjustable rear upper camber arms
Front & rear strut braces
Bridgestone potenza RE002 on stock rims (90% tread)
Nismo super coppermix twin plate clutch

Engine rebuilt at 137694km - March 2010
Cylinder head replaced (brand new) at 181085km - November 2013
Current km's 183182km

Tuned on 16 psi at the moment making 342hp. Very naice

Aww yeah. Legit one too. Needs a set of wheels and it has a few issues around the place. but has a lot of goodies

Trust sump extension

R33 GTR crank

HKS oil pump

ACL race bearings

ARP main & head studs

Eagle H-beam forged conrods

CP forged pistions 86.5mm

Ross metal jacket harmonic balancer

Tomei metal head gasket (oil restrictor fitted)

Tomei adjustable cam gears

Gates timing belt

Splitfire coilpacks

Nismo adjustable fuel pressure regulator

Nismo high flow fuel pump

Nismo low temp thermostat

Apexi power FC version 8.04a with hand controller

Garret GT2860R -7 turbos

HKS extension kit

HKS oil cooler & filter relocation kit

K&N reusable panel filter

Custom stainless exhaust 3" front pipes into 2.5"

DBA 4000 series rotors

EBC greenstuff pads up front, bendix ultimate rear

HSD HR coilovers

Billet aluminium rear subframe bushes

Adjustable rear upper camber arms

Front & rear strut braces

Bridgestone potenza RE002 on stock rims (90% tread)

Nismo super coppermix twin plate clutch

Engine rebuilt at 137694km - March 2010

Cylinder head replaced (brand new) at 181085km - November 2013

Current km's 183182km

Tuned on 16 psi at the moment making 342hp. Very naice

sounds good. When u buy?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...