Jump to content
SAU Community

Mugabetown - Whoretownin' At It's Worst.


Recommended Posts

Yes a special tool was cobbled together out of 3 x 1/4" extensions and a knuckle joint etc etc to narrowly avoid everything in the bay and latch onto the 14mm bolt, smashed it out in minutes.

Nope not in comp with Labdirect, so busy with my 'real' job that I don't have time to look at anything else at the moment :(

Today is a good day for a drive, methinks

Pete I would say radiator out, fan and clutch off, belts off, covers off, get it on top dead center, crack all the cam gear bolts before you losen the tensioner on the belt, mark edge of belt and gears with white out or paint pen, losten tensioner, slip belt off, carefully remove gears without turning cams, transfer marks from old gears to new ones, put back togeather the belt, turn the engine over by the crank bolt about 6-8 revolutions and then line the timing marks up again off the pulleys and block( the belt will be in a different spot)

If they all line up back togeather undo the tensioner and then retighten so it is seated right

Once tight, tighten cam pulley bolts and put it back togeather

While your in there I would recommend getting a timing belt kit, do the pulley's and seals same time

And also while you you are that far in you should probably do water pump

Pm me if you want and I can give you a full rundown but more descriptive

Pete I would say radiator out, fan and clutch off, belts off, covers off, get it on top dead center, crack all the cam gear bolts before you losen the tensioner on the belt, mark edge of belt and gears with white out or paint pen, losten tensioner, slip belt off, carefully remove gears without turning cams, transfer marks from old gears to new ones, put back togeather the belt, turn the engine over by the crank bolt about 6-8 revolutions and then line the timing marks up again off the pulleys and block( the belt will be in a different spot)

If they all line up back togeather undo the tensioner and then retighten so it is seated right

Once tight, tighten cam pulley bolts and put it back togeather

While your in there I would recommend getting a timing belt kit, do the pulley's and seals same time

And also while you you are that far in you should probably do water pump

Pm me if you want and I can give you a full rundown but more descriptive

or just give it to Zac to do :)

or just give it to Zac to do :)

Yeah but that costs lots of cash moneys

I can get a quote for Pete and let him know on Monday

Also Zac.........attachicon.gifImageUploadedBySAU Community1392450026.288363.jpgclutch fan and cooling fan is back in its place all shiny and stuff ;)

This makes Zac happy :)

Glad I could help

Pete I would say radiator out, fan and clutch off, belts off, covers off, get it on top dead center, crack all the cam gear bolts before you losen the tensioner on the belt, mark edge of belt and gears with white out or paint pen, losten tensioner, slip belt off, carefully remove gears without turning cams, transfer marks from old gears to new ones, put back togeather the belt, turn the engine over by the crank bolt about 6-8 revolutions and then line the timing marks up again off the pulleys and block( the belt will be in a different spot)

If they all line up back togeather undo the tensioner and then retighten so it is seated right

Once tight, tighten cam pulley bolts and put it back togeather

While your in there I would recommend getting a timing belt kit, do the pulley's and seals same time

And also while you you are that far in you should probably do water pump

Pm me if you want and I can give you a full rundown but more descriptive

Yeah, i've been digging through guides, process itself is pretty straight forward. Thanks for the tip of smashing off the cam gear belts before removing the tensioner, hadn't thought of that one.

Timing belt and pulley's have been done recently, unless the tensioner/water pump etc is obviously stuffed i probably won't bother replacing them, either way once i tear it down i can make a decision and get the parts before i put it back together again.

Then.. fuel pump, injectors and AFM.

Then getting the car to the workshop. I'm figuring flatbed may be the best bet, anyone know a good towing mob?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • The car/ECU will have all the sensor that it needs and expect to have. I think i do not have to explain to you how the Link is way better specialy if you have swapped engine   I just do not want to deal with any "problems" cuz i have only Nistune which i learned is not that great and in my case cant even deal with that speed problem (Link can) And of course it will be way more easier to tune and diagnose and safe. And for the ECU/speed problem...i dont know.
    • Per Mark Roberts of Sonictune: Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • Per Mark Roberts of Sonictune:     Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • The fancy pants red shock tower brace is finally incoming from MX5 Mania, getting it shipped from 'Merica has been a long and problematic process, and GWR, the 'Merican supplier will not ship directly to consumers outside of the US, Mania basically had to order a heap of them, the colour choice was silver, or red, and we all know anything red adds 5 killerwasps of dynotorques..... Whilst it does fit over a 2.5, and I've seen a few photos and videos of it being installed and fitting, google also says it might get real close to the FAB9 intake front runner, people in the US says it does fit with the FAB9 intake, except for one person who said it slightly touched.......so there is that.....LOL..... As it seems that I am the first in AU to have this combination of parts there's no local knowledge about fitment, so I'm just a willing guinea pig in this endeavour, I'll cross my fingers and toes and hope for the best In other news, I ordered stuff from China  on the same day I ordered the 23° silicone bend from Victoria, the stuff from China arrived a day ago, the 23° silicone bend is still travelling around Australia thanks to Australia Post, and "may" be here next week
    • Very good news...I contacted Racebox about it last night. My car is a 2016 so remains to be seen if it is compatible, requires a TCU swap, or is impossible.
×
×
  • Create New...