Jump to content
SAU Community

Recommended Posts

nice videos - looked like you pulled up short of the nuts :) Had to lol a little when you turned the wheel well after it was all locked up though! hehe

I've got to say I think you should be in the Modified Road Registered class rather than the Production Road Reg class. Car looks modified to me! Good to see more Jap turbo cars turning up out there :)

Edited by hrd-hr30

nice videos - looked like you pulled up short of the nuts :) Had to lol a little when you turned the wheel well after it was all locked up though! hehe

I've got to say I think you should be in the Modified Road Registered class rather than the Production Road Reg class. Car looks modified to me! Good to see more Jap turbo cars turning up out there :)

Turning the wheel You can only but try/hope.... :whistling:

Cars pretty much stock....Build to production sports car CAMs specs.... Stock ecu, turbo, inlet, outlet manifold, stock brakes, motor.... Only real mods is the camber arms and coil overs, cage so I have a fighting chance if I go over on my lid. I don't care what class I was in, just turned up for fun. It will be a once a year thing for me. Could be worse, look at the AC cobra.... Built DJR race motor, hoilenger gear box, nissan diff.... Running in MK sports....

I can see your perspective, but it isn't CAMS Production Sports Car racing, it's a class MGCCQ made to give near stock road cars a class to race in away from the stripped-out, caged-up race cars they were previously luimped in with. Cars are supposed to comply with QLD Transport rules and must have a cat. Minimal mods allowed in Prod Road Reg, basically exhaust, springs and shocks. Any more than that and it's in Modified Road Reg. At least that's the way they explained it to me before I entered. When I was getting close to the record I had officials checking if I had a pod filter or intercooler!

Edited by hrd-hr30

Was entered as Mk Sports..... people complained, It's listed under CAMs as a sports car, but not under FIA.

Then they enter me as 4 wheel drive Forced induction..... My car is 2 wheel drive

Then Mod production car.... Someone complained because I was not entered in the series and would muck up there points... Plus it's a sports car not a production car.....

All the other R33s GTST where entered in the Inv cars class, the other drivers where o.k. with it be cause my car was pretty much stock other than the cage which weights 80 plus kg.... Pretty much about the same as a interior of the car. Still got electric windows and mirrors, on road tires.....I just wanted to have a some fun....... Which I did....

But it's motor sport...Every ones got a opinion.....Whinny bottoms are going to Whinny bottom..... ;)

  • 4 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
×
×
  • Create New...