Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...

Finally got the rears fitted today. So glad it all just works. Such a relief!

I'm now going to finalise the order for the motorsport spec bearings (unlike other kits on the market, they will use proper motorsport/aircraft spec bearings which have much tighter tolerances. I have used the highest quality materials in this design so no point skimping there either. Will add a bit more cost but it's well worth it.

dr30-skyline-s13-silvia-rear-strut-top-c

Much more height available now - with the standard S13 rear struts at full extension they were well below normal DR30 ride height. With these you can now get a standard ride height without having to be at full extension meaning the car will ride a heap better.

dr30-skyline-s13-silvia-rear-strut-top-c

dr30-skyline-s13-silvia-rear-strut-top-cdr30-skyline-s13-silvia-rear-strut-top-c

Hey guys,

I have some pricing and these kits are selling now. I am awaiting final delivery of the new bearings and as soon as they arrive I can start shipping. I have a front set sold already already so currently have:

8 fronts left

9 rears

Front and rear kit as a package is $350

Front alone is $220

Rear alone (will also fit R31) is $160

You can purchase via my website www.brysport.com/shop.html

Also have a few more exciting DR30 and FJ20 bits coming...

7 fronts left

8 rears

Just to let you know the bearing hold-up has been sorted but still a couple of weeks away. Still taking orders as they will be shipped as soon as the bearings arrive.

No hold up if you just want rears. Can be purchased through: http://www.brysport.com/shop.html

  • 4 weeks later...

The bearings have finally arrived and they were worth the wait. You will never get a kit like this with these motorsport spec bearings at this price. These spec bearings alone are RRP $180 a pair - just ask anyone who has had to build a race car before and had to spend thousands alone on bearings!

I have a few sets left so please visit the website and make your purchase for the complete kit, front or rear alone.

http://brysport.com/shop.html

  • 3 weeks later...

Hi there, I've just check my inbox and nothing there, please send to [email protected] - or send me a message on here.

As far as fitment on the C210 if the tie-rod-ends are the same ar the R30 then this kit could probably be used with the C210 but I have never seen a C210 front end. Could you send me photos of the tie rod end along with some measurements?

  • 3 months later...
  • 2 months later...
  • 1 year later...

Pics are all dead, I was wondering if these kits would suit a 88 Z31 300ZX. S13 based conversions have been done in the US and as far as I can tell the Skyline suspension setup is similar to the Z31's. Old thread I know, no harm asking though.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...