Jump to content
SAU Community

Recommended Posts

Legal size for what?? As long as most of the tyre is cover by an arch of some sort then it can be as wide as you like!

not in NSW without and engineers report.

legally ypu can go 1 inch wider and 1 taller then the largest option in the placard.

so, non vspec, will be 17x9

vspec should be 18x10 (I think, cant recall width of bbs)

still has to be within guards, not foul aywhere on body or chassis, and not increase track by more then 1inch.

Are you planning on running staggered sizes? Because you'll have a bad time.

I run 18x10 +20 with 265/35/18. Guards have to be lipped and run some negative camber.

Would 18x10 +25 or +30 make things a little easier?

Not sure, I haven't measured the gap between wheel and struts. But it looks like there isn't much room left. +25 *might* hit the struts depending on what you're running.

Perhaps run a 9.5 +22? You can still slap 265/35/18 on them and it'll fit. Note that tyre design plays a part in fitment as well. The old Potenza tyres that came with the wheels had a more stretched design compared to the Falken FK452 on there at the moment. The Bridgestones fitted without rolling the guards, but the Falkens rubbed (bought a guard roller + heat gun and rolled the guards).

vspec should be 18x10 (I think, cant recall width of bbs)

I'm pretty sure R32 V-Spec BBS are 17x8 +30
  • 9 months later...

Would 18x10 +25 or +30 make things a little easier?

i am at this point where i also want to know if running +25 or +30 will avoid having to roll guards?

anyone out there running this offset?

I ended up getting 10.5 +25, trial fit of the wheels without tyres was fine. I now have 265/35s fitted but haven't had time to try them yet. I'm concerned about how the curve of the front upright comes in (toward where the tyre will be) where it mounts onto the upper arm. Might get tight there. I have already rolled my rear guards - i needed that for 255s on +20s on tyres with a generous treadwidth (IIRC the Falken RT-615 scrubbed but whatever was on there before didnt).

Well with my 19x9.5+25 i have sfa between the front upper arm and tyre. Im running stretched 245s pirelli p zeros.

Adam, your wheels have 13mm less clearance than my above setup but running 18s should help with smaller rolling diameter...hmmm

I ended up getting 10.5 +25, trial fit of the wheels without tyres was fine. I now have 265/35s fitted but haven't had time to try them yet. I'm concerned about how the curve of the front upright comes in (toward where the tyre will be) where it mounts onto the upper arm. Might get tight there. I have already rolled my rear guards - i needed that for 255s on +20s on tyres with a generous treadwidth (IIRC the Falken RT-615 scrubbed but whatever was on there before didnt).

did u end up fitting your tyres yet?

I've trial fitted a front +25 wheel with a 265 and there's ~9mm clearance to the curved upright. so that looks fine. I haven't tried a rear or driven it yet - need to fix an oil leak first...

My thinking was that since 255s on a +30 rim worked, 265s on a +25 would have the same clearance to the upright. Of course i then found that the Dunlop 265s were about 20mm wider at the tread than the Toyo 255s...

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...