Jump to content
SAU Community

Recommended Posts

hi guys , problem, ive gone to install rack spacers in an r32 and it seems the teeth on the shaft wont allow it to go in further????

it gets to the rack and stops flush and feels like the teeth are maxing? the other side goes in HEAPS!! anybody had this problem before?

Link to comment
https://www.sau.com.au/forums/topic/438079-lock-spacers-not-working/
Share on other sites

yea man droped both sides so just the rack. have done this on my c33, albeit with some other over the top mods and no probs. will chuck pics tomorrow . measurements at a guess would be 2mm below flush on drivers/pinion side and 20-25mm on other

Edited by missile_c33

Yeah if thats what your getting then you need to run the offset spacers like these ones.

http://www.gktech.com/index.php/4130-high-tensile-steel-steering-rack-spacer-set.html

so you will put the big spacer on the passenger side since it has more travel and small spacer on driver side then you just recentre the rack to even it out.

Recentreing is simple. First install those offset spacers plus your tie rods, then go lock to lock and coubt the turns it takes then go back half way and that will be your new centre position for your rack.

You now set your toe settings from this new centre position.

Edited by boostn0199

oh yea, i know that (haha) it just seems to run out of teeth to pull the drivers wheel in, ill take pics and try get them up on here

Yeah thats why u recentre it so in other words after you recentre it the rack wont be at equal lengths at each side to compensate for the extra travel on one side.

For example like you said you have 3mm travel on your drivers side and say 12mm on your passenger side. If the rack is left in its centre position like normal you will get more lock and one side due to the extra travel so when you recentre it to its new centre position which would be 4.5mm off the normal centre towards the drivers side you will now have 7mm travel each side asappose to before where it was 12 on one and 3 on the other.

I know its hard to understand from reading it but might help if I draw a diagram.

yea makes sense and REALLY appreciate the help, what i shood have said also is im using offset rack spacers. so when i go full lock right, with offset spacer on, lock nut off tierod and wound right in (cut to go all the way) so everything in as far as possible, it doesnt hit lock stops, maybe no use offsets or affter market tierods?

I had the same problem with my 33 well all 33 seem to do it when you add washers for more lock.. I think its just in the design of the rack, turning left always has more travel. If just got my knuckles modified, were they shorten and straighten the tie rod arm(cut and weld) gets heaps of lock combined with a slip on washer. The advantage is it reduces akerman between the two wheels and also shortens the steering ratio(less turns lock to lock. Win win for a drifter. JDI fabrications do them in Melbourne.

I had the same problem with my 33 well all 33 seem to do it when you add washers for more lock.. I think its just in the design of the rack, turning left always has more travel. If just got my knuckles modified, were they shorten and straighten the tie rod arm(cut and weld) gets heaps of lock combined with a slip on washer. The advantage is it reduces akerman between the two wheels and also shortens the steering ratio(less turns lock to lock. Win win for a drifter. JDI fabrications do them in Melbourne.

Really your 33 rack does that? The 6 ive gone through all only have 4mm extra travel each side.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I get that taking off the head is best but that's a bit much for "just" valve seals. I was just under the impression that one would be able to rotate to TDC and be able to temporarily drop the valve without losing it and effectively having to remove the head to then recover it. I never knew people actually pushed rope into the cylinder to do valve seals hahaha So just to confirm, just going to TDC will not work? In that case I know when I do valve seals I'll maybe just remove the head and do some other things while I'm there, or just wait until I do an engine build.
    • The old approach was to fill the cylinder/chamber with a length of rope pushed in through the sparkplug hole. The new approach is to connect compressed air to the sparkplug hole and fill it with enough pressure to push the valves up. Doing either of these things with the head on and the engine in the car is a lot less pleasant than doing it properly.
    • Can't you put the pistons to TDC and then do the valve seals? Or will the drop down too far to pull them back up?
    • One thing I can tell you is, do it properly the first time. If you encounter unexpected problems just let the car sit for a week or two if you have to get some other parts or figure stuff out.  I'd have said go and use as many OEM parts as possible but since you want to change the turbo later on a custom kit is probably the better choice. Since I have no experience with RB25 just compare parts diagrams and images before buying a line kit and it should be easy to see if it has everything you need. Amayama has very good parts diagrams and part number lists, that is what I used a bunch to figure out what I might need. And don't forget to plan ahead and possibly renew other stuff that's easy to get to while you're in there doing the turbo lines. Happy wrenching
    • Update 4:   Hi all, good news. Engine is running and all the gaskets and seals seem to be working as intended. No leaks so far, even the JB Weld seems to hold. I flushed out the old coolant a few times and put in fresh coolant, not Nissan stuff, I decided to try the Ravenol Protect FL22, they claim it works for a wide variety of JDM cars and the opinions on it by some people were pretty good. And it has the nice poison green color! And man am I glad I bought a coolant system tester earlier this year, vacuum filling works wonders on this engine. I can definitely recommend this to anyone still doing it the old school way. All you need is compressed air supply. Will have to do a small test drive as soon as I can, I removed the gauge cluster again as the tacho needle was still bouncing around a bit but it was much better than before already.  I also found some cracks on all 4 tires inner and outer sidewalls. Apparently these tires should 't be parked on for extended periods or be kept under 0 degrees during storage, which I did not know. Clearly the previous owner didn't look into those details either, he probably bought them just cause they are cool semi-slicks. I'm just wondering how tf I am supposed to reach 30-80 degree tire temperatures on the public road consistenly, these tires were never going to work for my use case. I'll probably order Continental SportContact7 ones as these are the best allround summer tire available right now and I don't think I'll need anything crazier for now. Do let me know if you have experience with various tires and which ones you recommend.
×
×
  • Create New...