Jump to content
SAU Community

Recommended Posts

Hi mate.

I have spent a lot time building power, but now I know a lowered r33 gtst has no grip off the line.

I had a mustang before and I had set that up for good launching the advantage I noticed is that the mustang had a solid axle and the geometry of the suspension was way better for drag racing. I think this is because the mustang always through out the whole weight transfer kept the tires flat.

But with the skyline being lowered I'm already at a disadvantage cause my camber in the rear is off and I'm riding on the inside off the tire to begin with. Now when the car is leaving the line it flexes to transfer the weight and the rear wheels go even more off camber. More on the inside edge of the tire. Hence the car can't dig in.

Does anyone have any experience with a good drag setup. Like the shocks I need and what Kg springs to use. Along with the hight from fender to middle of the axle. I'm also thinking of pineapples (don't know if they work) along with some arms to adjust the rear camber and toe of the rear wheels.

Any imputs would be helpful.

Thanks mate

Link to comment
https://www.sau.com.au/forums/topic/438288-drag-suspension-setup/
Share on other sites

I was hoping for a more detailed explanation. Trust me i started out with that. It's not going to be that good. I feel that the hight needs to be raised about 365mm from fender edge to axle and some soft springs. And start off with about +1 camber.

Well your on the right track. The principles apply from the Mustang to the Skyline.

The one major difference being IRS. A raised ride height and some positive camber will help traction off the line.

Also, what tyres are you running and how much power?

The pineapples are for the skyline R33 gtst. The power is about 420hp. It's not that much but right now it's just spinning up the tires. Even with the stock rear shocks and springs. I have also changed my driving style and nothing is helping to much.

I'm looking at the titan supra for clues. I notice that it has to be real soft. With good shock dampening. To work. But do I need to also raise the front of the car as well or just the rear.

I'm just using my old set up on my mustang as a comparison. Where the skyline leaves the line spinning the wheels I had way more power in my mustang with way more toque in the past but it just took of way faster. But the skyline is way stronger mid track. I feel if I can get the right setup I would love this car. I have the car set up with down graded s13 rear brakes and have a set of weld racing rims and 10x26x15 micky Thompson et drags to run.

I just need help finding the ride hight and shock and spring rate to start out with. I'll post a video of a friend driving my old mustang (I sold it) against the skyline. At only 7 psi. A bit later. Thanks mates.

My i add that the mustang is running full stocker 346 with full drag suspension. And NT555 tires. I feel if i run my gtst at 18 psi i can run it down. But that's not my interest. I just want to launch the same way.

Adding 90/10 shocks with standard springs will help but I think the main thing will be the ET streets.

If the car is manual then leaving the line with boost will also be difficult. It's either dump the clutch at 6000rpm+ or bog down.

Maybe try to set up some kind of 2 step limiter for launch?

Its all been covered here.

Most people find the stock suspesion setup is best including the factory soft spring rates.

Watch and try to measure/workout the rear squat on launch, a little positive camber on the rear when unloaded will turn to no camber on launch for the best rear footprint so you need to set it up with no camber when at the launch/loaded ride height.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
×
×
  • Create New...