Jump to content
SAU Community

Nsw: Npc Carbotic Clutch And Rb25 Flywheel

Run-It-Hard
 Share

Recommended Posts

Run-It-Hard Veteran

Run-It-Hard

Posted
Posted (edited)

NPC-carbotic-5-puk-clutch-installed.jpg

Hey guys,

Got a NPC carbotic 5 puk clutch and flywheel off my R33 Skyline that I've been wrecking recently. It's near new (less than 3000kms old) and has been a great setup.

Nice soft pedal feel with a ton of bite. These clutches handle any abuse you can throw at it and are rated at some silly power figure (400ishkw). Very streetable clutch.

Will also fit R32 GTR (push type gearbox)

I'm after $650 ono

Hoxton Park region

Happy to ship at buyers expense.

get me on 0490169671

Adam.

Edited by Run-It-Hard
Run-It-Hard Veteran

Run-It-Hard

Posted
  • Author
Posted

I don't think it will as R34 are pull type.

It's a standard RB25 flywheel, just easier to use this as it wont need machining.

It has seen 1 track day since it was run in/installed.

  • 2 weeks later...
  • 9 months later...
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Wheel Sizes & Offsets For Skylines

      By GTSBoy · Posted

      9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • Dose Pipe Sutututu
      RB25DE NEO with Haltech ECU

      By Dose Pipe Sutututu · Posted

      post up screen shots of your injector tables
    • joshuaho96
      R34 25GT Engine Light 21

      By joshuaho96 · Posted

      Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • feartherb26
      RB25DE NEO with Haltech ECU

      By feartherb26 · Posted

      I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
    • Black_CSR
      Wheel Sizes & Offsets For Skylines

      By Black_CSR · Posted

      yeh they are 235/45/17 up front and 255/40/17 in the rears. I still didn't get my answer if i can fit a 18x9 up front. I want to get 4 of this and see if they will fit before committing as they didn't see an 18x8 as an option but there is a 18x9.5 also.   Enkei RS05-RR 18x9 35mm ET 5x114.3 75.0 Bore Matte Gunmetal Wheel
×
×
  • Create New...