Jump to content
SAU Community

Recommended Posts

Had this turbo for my RB20, backed to back it against the TD06-20G and despite the bigger compressor gave away nothing to the 20G in response, in fact it did seem to spool up nicer on the limited street driving it did.

So has done some dyno time and about 20kms of street driving. Removed it as the 12cm housing simply was too big and 8cm too small.

On an RB20 with an 8cm housing would be a very good thing able to make 310-330rwks depending on mods (inc E85). On an RB25 with a 10cm housing would be a very good thing, with almost T67 power but with better response of the 20G

Runs a late model 65mm turbine that all the high performance turbos on late model EVOs run. Flows better than the L2 turbine.

Only reason I am selling is because I am unable to find a 10cm Trust housing for it. So running my T67 with 10cm housing. (That and also my new engine has weak valve springs and cant run over 18psi so cant get the best out of the billet wheel, so T67 is getting the job done)

If you can get a 10cm T3 housing will be a very good turbo for an RB25. An 8cm would be a better setup then a 20G


73HTA Billet Compressor by Forced Performance
med_gallery_462_50_36538.jpg
med_gallery_462_50_177446.jpg
med_gallery_462_50_151826.jpg


Side by Side with TD06-25G
med_gallery_462_50_113969.jpg
med_gallery_462_50_7215.jpg
med_gallery_462_50_180417.jpg

Asking $850
Link to comment
https://www.sau.com.au/forums/topic/438894-td06-73hta/
Share on other sites

  • 2 weeks later...

So can you get t3 10cm housings from kando for the td06 20g billet Roy? I know the feeling of having a build up of parts sitting in a room doing F ALL LOL.

Link to comment
https://www.sau.com.au/forums/topic/438894-td06-73hta/#findComment-7207073
Share on other sites

  • 2 weeks later...

I have a 10cm rear housing for sales...modified with 44mm TIAL gate ...bolts to stock manifold and comes with dump pipes...

if any one is interested.. :D see my link below...

\

If i had spare cash i most definately would of bought this off you Roy and stretched the legs on the old RB...I know it would be an amazing turbo to run...

Instead I bought a Toyota... I would happily bolt it to the Toyota too, but then theres tuning and what not...

Link to comment
https://www.sau.com.au/forums/topic/438894-td06-73hta/#findComment-7225787
Share on other sites

  • 1 month later...
  • 4 weeks later...
  • 2 months later...

Just updating the link to the exhaust housing you need to run this on your RB25

http://www.ebay.com.au/itm/Kinugawa-Turbine-Housing-STD-TD06-T3-Flange-10cm-A-R-73-V-Band-External-Gate-/281406096058?pt=AU_Car_Parts_Accessories&hash=item41851c42ba

Slap that housing on the turbo and with whatever manifold you are running.....or weld the gate to the turbine housing to bolt it on to the std manifold and make a responsive 330-350rwkws on E85

Link to comment
https://www.sau.com.au/forums/topic/438894-td06-73hta/#findComment-7372835
Share on other sites

  • 3 months later...

I still live in hope that I can find a Trust TD06 10cm housing but to date have not been able to...so if someone wants to take this off my hands its sitting in a box and a friend that was keen to try it on his S13 has not lost interest in his project...so desire to hold onto it is now fading

Also, it someone wants my genuine Trust T67 and 6boost setup I will part with it and use the 73HTA on std manifold with gate welded to housing

Link to comment
https://www.sau.com.au/forums/topic/438894-td06-73hta/#findComment-7437926
Share on other sites

  • 5 months later...
  • 9 months later...

So i sold the T67 setup with gate manifold with a view of running this on a std manifold with gate welded to it...but decided to stay the course and finish my new motor with twins

So the turbo now has a new T3 10cm housing making it pefect for RB25. I still have the 12cm housing but that has the Trust 3 bolt flange, but hey if you prefer that housing i can swap it back to the 12cm

gallery_462_50_285325.jpg

gallery_462_50_1348940.jpg

gallery_462_50_548485.jpg

gallery_462_50_966223.jpg

With housing ready to go $1000

If you do searches for FP Green turbos which run this exact compressor and an older version of this turbine you will see on Evos they often make ~450awhp on E85...

http://www.forcedperformance.net/merchant2/merchant.mvc?Screen=PROD&Store_Code=FP&Product_Code=NTDSMFPGREEN&Category_Code=Holidaysales

Link to comment
https://www.sau.com.au/forums/topic/438894-td06-73hta/#findComment-7685552
Share on other sites

As per pms'....if you are running 98 fuel i dont think there will be much difference between this and a 20G. A handful of kws and a beeds dixk in response. If you run E85 where the 20G will stop making power at 20-21psi this will keep on gunning and making power at higher boost

Link to comment
https://www.sau.com.au/forums/topic/438894-td06-73hta/#findComment-7686376
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Sounds good Hmm suppose the main thing is, how much do you care about this car? The filler doesn't make for a very good water barrier lol. If there was a tiny little bit of rust forming now, that in 3 to 5 years time becomes obvious under the paint (starts to bubble up), would it bother you? 
    • I already have the ability to datalog the voltage... what I can't do is correlate it to what the gauge is showing when I'm looking at the data at a later date. Or something like this. Except getting the oil to 125C+ involves me going 200+kmh at the track so you can imagine this is a little tricky unless I do something like note what the voltage is when I am at the top of 5th gear so I have a point to reference on. Drove car today. O2 still reading richer because hopefully not a leak instead of massive restriction I've introduced. Car really doesn't sound like a LS. It's quite strange. Pulled a bit of fuel out up top. This does potentially explain why my spark plugs looked like the car was running pretty over-rich. If I was tuning it to a ~12.7 which in reality was far richer than that in the past. It will be handy to have the dyno WB to compare my WB to to compare notes that's for sure. At this point I'm happy to just sit in the passenger seat and tune the thing given I've got about 7 million hours on the platform lol.
    • Yeah I understand you have to pay for an updated map or subscription service or something. But I can't even find a current map for Australia. My map is dated 2017, but didn't this car version still sell in Australia until 2021?   Also, just as an aside, the navigation system warns you of traffic incidences ahead.....why would they include that on a map they knew is not receiving live information. I am forever going to be warned of an incident that probably existed for 30 minutes 8 years ago.
    • Car has been sold and I am now selling leftover parts. Prices are non-negotiable as I will sell to my mechanic if it won't sell here. Prices are firm except for the Random Parts listed at the very bottom. All parts are genuine except for the S-Tune front bumper. Volk Racing TE37SL 19×10.5″ +12 5×114.3 pressed graphite with P-Zero 275 30 19 tyres [USED] $4,500 Wheels are in perfect condition, have been sitting in my garage for the past 6 years. Tyres still have 90% tread, but since they're now old, I would not recommend you drive hard on them. K-Sport Super Sport External Reservoir Coilovers (made to order) [NEW] $2,500 Front spring rate 14kg, Rear spring rate 7.5kg Fork Type. You can read all about it here (https://www.k-sportracing.com/product_detail.php?Key=12). I was going to start tracking the GTR, but never got around to it. Paid $3500 (after USD conversion and taxes). HKS Kansai Service Tower Bar [NEW] $500 Never fitted in the original Japanese box. R34 GTR S-Tune Fibreglass Bumper [NEW] $500 No mesh - No Box - No damage - just dusty. Nitto RB26 Clear Timing Cover [NEW] $50 Couldn't fit RB2630 due to bonnet clearance. HKS Piping Kit Special Type (BNR34) & Apexi Power Intake Air Filter Kit & Password JDM Adapter [USED] $1,000 Missing some rubber hoses and supports, but you get what you see. Nismo NE-1 Weldina Turbo Back Exhaust & Custom 3.5"straight pipe [USED] $1,000 Needs some love, but perfect for those who want to go back to OEM+. Bayside Blue Aluminium Vspec Bonnet/Hood [USED] $700 Came off my GTR. Unfortunately, the tips have been slightly ground down. It will need some repairing. Bride Low Max Super Seat Rails [USED] $350 The price is for both sides. Will post pictures when I get a chance. Random Parts [USED] - negotiable Standard rb26 cams (intake and exhaust) $10 Stock amber front indicators $10 Standard GTR bumper lower side grills $10 Stock amber side indicators $10 Nismo Sports Resetting ECU $50 Water reservoir $10 Stock airbox mouth $10 Stock fuel rail $10 Stock coilovers from R34 GTR Vspec $100 PM me which items you are interested in. I do work 9-5, so I will be responding daily at best. Best time for pick up is after 5 and before 7 on weekdays, or i can work something out on weekends. I will only accept cash or PayID. Pick up only - located Epping NSW area.
    • sensible choice....and all 32s should be in yellow
×
×
  • Create New...