Jump to content
SAU Community

Recommended Posts

Hey guys, pod on my car is currently sitting near wheel arch... I know... I know... I bought it like that and have a pipe being made up to be able to sit it up top again. But anyway, I was driving home from work tonight, and it began to rain, I didn't go through puddles or anything remotely close to it, but the water from the rain was causing the car to drive pretty, then it also stalled out a couple of times. Could this effect my engine in anyway? as I said, the pod was at no point fully submerged in water or even close to it. But if it was sucking in the rain water, can that cause any damage to my engine.

I don't drive at all when its raining, its just tonight it decided to start raining while I was driving home from work -_- really hope I haven't caused any damage.

Link to comment
https://www.sau.com.au/forums/topic/439570-water-and-pods/
Share on other sites

My cold air intake draws from in front of the passenger's wheel. Not one drop of water goes up into the factory airbox from there. A pod hung in that location should also be fine.

A wet pod filter or wet AFM will generally cause trouble though. Did you feel the pod to see how wet it got?

Link to comment
https://www.sau.com.au/forums/topic/439570-water-and-pods/#findComment-7207690
Share on other sites

When I had my XR6 Turbo with pod in the guard I sucked a lot of water in one day and the car stalled. I got all the water out and let it sit over night.

I started it the next day and it ran a little rough but eventually dried up.

Link to comment
https://www.sau.com.au/forums/topic/439570-water-and-pods/#findComment-7207699
Share on other sites

Unless you hit a big puddle and water splashes hard you wont notice any problems and even if you do and abit of wAter goes into the afm you might start to have a missfire but will go away once it dries up.

Link to comment
https://www.sau.com.au/forums/topic/439570-water-and-pods/#findComment-7207700
Share on other sites

Yeah true. One of my friends had the same problem, but he unfortunately went through a puddle, and the whole pod was submerged in water and sucked a shitload in. Blew his engine two weeks later. So the main thing im asking is, as long as the pods not fully submerged, a little bit of water isn't going to effect the engine? I plan on fixing this asap just for peace of mind lol. The rain wasn't real hard, but it was causing the car to stall out a couple, sitting on the side of the road starting my car a couple times wasn't fun haha.

Link to comment
https://www.sau.com.au/forums/topic/439570-water-and-pods/#findComment-7207971
Share on other sites

Is there a way of checking these things or? sorry guys, Im pretty paranoid about keeping my car healthy, going to uni atm and dont have the dollars for a new rebuild But I love my skyline too much to sell it. Would checking the oil for milky deposits be a good indication whether water has gotten that far? I know that im probably just being paranoid.

Link to comment
https://www.sau.com.au/forums/topic/439570-water-and-pods/#findComment-7207999
Share on other sites

If you're that paranoid, just take out the cooler and let it drip into a container and check the oil that comes out of it. depending on your setup, cover the hole that the old smic has left, and make a cover for the pod blocking off the headlight etc... Put the standard airbox back in.

But really you're just being paranoid. ;) Just don't flog it when it rains, and steer away from puddles.

Link to comment
https://www.sau.com.au/forums/topic/439570-water-and-pods/#findComment-7208009
Share on other sites

If water was to do any damage, it would be done by now. If you car drives and runs, then its ok I'd say.

If you paranoid about driving in the rain either get a stock airbox or possible make a shield for relocate the pod...

Link to comment
https://www.sau.com.au/forums/topic/439570-water-and-pods/#findComment-7208044
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Sounds good.  I don't 100% understand what your getting at here. When you say, "I keep seeing YouTube videos where people have new paint and primer land on the old clearcoat that isn't even dulled down" do you mean this - there is a panel with factory paint, without any prep work, they paint the entire panel with primer, then colour then clear?  If that's what you mean, sure it will "stick" for a year, 2 years, maybe 3 years? Who knows. But at some stage it will flake off and when it does it's going to come off in huge chunks and look horrific.  Of course read your technical data sheet for your paint, but generally speaking, you can apply primer to a scuffed/prepped clear coat. Generally speaking, I wouldn't do this. I would scuff/prep the clear and then lay colour then clear. Adding the primer to these steps just adds cost and time. It will stick to the clear coat provided it has been appropriately scuffed/prepped first.  When you say, "but the new paint is landing on the old clearcoat" I am imagining someone not masking up the car and just letting overspray go wherever it wants. Surely this isn't what you mean?  So I'll assume the following scenario - there is a small scratch. The person manages to somehow fill the scratch and now has a perfectly flat surface. They then spray colour and clear over this small masked off section of the car. Is this what you mean? If this is the case, yes the new paint will eventually flake off in X number of years time.  The easy solution is to scuff/prep all of the paint that hasn't been masked off in the repair area then lay the paint.  So you want to prep the surface, lay primer, then lay filler, then lay primer, then colour, then clear?  Life seems so much simpler if you prep, fill, primer, colour then clear.  There are very few reasons to go to bare metal. Chasing rust is a good example of why you'd go to bare metal.  A simple dent, there is no way in hell I'm going to bare metal for that repair. I've got enough on my plate without creating extra work for myself lol. 
    • Hi, Got the membership renewal email but haven't acted yet.  I need to change my address first. So if somebody can email me so I can change it that would be good.    
    • Bit of a similar question, apprently with epoxy primer you can just sand the panel to 240 grit then apply it and put body filler on top. So does that basically mean you almost never have to go to bare metal for simple dents?
    • Good to hear. Hopefully you're happy enough not to notice when driving and just enjoy yourself.
    • I mean, most of us just love cars. Doesnt necessarily have to be a skyline.
×
×
  • Create New...