Jump to content
SAU Community

Recommended Posts

Hi all,

I am taking out the drive shafts to replace both inner CV Boots on an R34 GT-R. I have taken out the passenger side drive shaft out no worries but I am having difficulty pulling out the drivers side. Going off the workshop manual for an R32 GT-R (cant find R34's) it says that you have to drain oil from Front Diff, remove cover, remove C-clip then wedge out the drive shaft...

My problem is removing the front diff cover. I have unbolted all 10 x 14mm bolts holding the cover in place but the cover seems to be really sealed on to the diff & I just cant get it off :(

Anyone had this issue before? Any help/info/tips would be greatly appreciated :yes:

Cheers,

Glen

Edited by xanavinismo

Should just come off, its probably silicon holding it on, yes 10 screws after counting them on my diff..

Watch the breather tube on top too.

You just pry the shaft out using a big screw driver from inside the diff, the clip just hops over the cut in the shaft.

I am not certain that r34 is the same, but on 32-33 it is possible to remove it without removing the diff cover (bit late now!). You can pop the driveshaft out even if the circlip is in place using a pry bar. The other end is trickier, I've found the easiest is to remove the lower control arm at the ball joint at the hub.

Thanks for the feedback guys!

So where exactly do I pry it from? Eg - Up against the diff?

Also when it comes to putting the drivers side drive shaft back in, there wont be any issues with lining it up with the circlip inside the diff etc?

Cheers guys!

Glen

You just need to pry between the inner joint cup & the diff housing.

For refitting the shaft, ensure the circlip is a snuggish fit into the groove (if its not, then it will catch on the spline & be forced out of the groove & possibly damaged), start the splines in the carrier & drive/force it in BY HAND. The circlip will compress.

You just need to pry between the inner joint cup & the diff housing.

Do I also need to pull & rotate the driveshaft while prying? Because my problem is that the inner CV boot is completely split and theres nothing keeping the shaft in place :(

IMG00349_20140310_1253.jpg

No, it should just pop out, its just a matter of finding the right place to lever. I have to do mine soon too, would have done already except for a back injury.

You can remove the shaft from the cup, just be careful as there are three races with needle rollers that can fall off (dont lose any, as re-assembly with just one missing means failure). Then you can pop the cup out of the diff.

After many attempts to pry the shaft out still no success :( So I moved back onto removing front diff cover...

Okay so I finally removed diff cover (ableit using a razor blade to cut the silicon bond in between the diff housing/case.

IMG00353_20140311_1354.jpg

Next issue is where exactly do I pry from? The workshop manual for an R32 GT-R isnt showing exactly where to push up against...

ttttt.jpg
Thanks again for the help guys!
Edited by xanavinismo

Do I also need to pull & rotate the driveshaft while prying? Because my problem is that the inner CV boot is completely split and theres nothing keeping the shaft in place :(

IMG00349_20140310_1253.jpg

sorry for the slow response....it must be frustrating getting stuck at this bloody spot!

Basically I would get a pry bar (maybe very small at first, maybe even a screwdrive if the fit is very tight) into the area pictured. The end of the drive shaft and the bronze coloured steel shield come out together, so get the bar underneath that bronzy disk and start prying. As it can require some force be careful.....levering stuff out is a really good way to hurt yourself when it does finally let go!

Or, since you have the cap off, in the diff centre as pictured are 2 small spider gears, the end of the driveshaft is inside the spider gear and you should be able to get something in there to pry it out too....the pic doesn't really show it because you are looking straight on, try looking from the right side back to the left and you should see the end of the shaft.

Failing all that....whereabouts are you? I'm actually in Canberra tomorrow night and can give you a quick hand if you haven't won....

I haven't done it on a gtr, but with the circlips holding in drive shafts prying as hard as you can sometimes doesn't cut it. A quick sharp blow on the pry bar shocks them free. Also when doing that push it in as far as you can so it gets a little 'run up' to pop out.

sorry for the slow response....it must be frustrating getting stuck at this bloody spot!

Failing all that....whereabouts are you? I'm actually in Canberra tomorrow night and can give you a quick hand if you haven't won....

Yes very frustrating indeed :(

But wow what a coincidence, your in Canberra! Im up in the northside of Canberra. Would be really appreciated if you can come over and give me a hand! :yes: I can PM you my address...

I am happy to report that I have finally managed to wedge out the driveshaft! Wooohoo!

I did it via wedging from inside the diff with a small pry bar/screw driver & using a hammer to give it that shock to release the circlip, for me a much easier option then somehow prying like you guys. Hats off to those who are able to pull it out that way :yes:

IMG00364_20140312_1334.jpg
IMG00367_20140312_1335.jpg
Thanks again so much to all that gave me their helpful details/hints/tips!
Cheers,
Glen
  • Like 1

Good work! Some thought out hammer blows make all the difference.

Same goes for tight nuts, ball joints etc, a sharp blow works so much better than a levering action.

It's science :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...