Jump to content
SAU Community

Recommended Posts

Thought I'd share this engine with you...

442ci General Motors based OHV V8

- no gaskets, just heat expanding O-rings

- extesive use of titanium.

- fluid dynamic crank to cut through the oil easier at speed

- turbos similar spec to what is found on Indy cars

Capable of 10000RPM (not bad for a 7.2L engine)

Early dyno run @ 25psi

1820Nm @ 7500RPM

2140hp @ 9000RPM

aiming for 2800hp with the boost set at 35psi

just the ticket for getting to work in my R32...

Link to comment
https://www.sau.com.au/forums/topic/44072-who-here-likes-nm/
Share on other sites

timbar32

it says 10,000RPM not 100,000RPM. Its not a turbine....

the type racing this will be used for involves a lot of runs per meet, so it has been engineered to produce this power consistantly with needing a rebuild every run.

Basically nothing in the entire engine is off the shelf. Even the cam is considerably thicker than in the engine its based on. The write up on this suggests rather extreme levels of engineering.

7.2L, 4 turbos & 10,000RPM would sound unbelievable on the track

Link to comment
https://www.sau.com.au/forums/topic/44072-who-here-likes-nm/#findComment-900725
Share on other sites

nah, the guy is fairly tight lipped about many of the exact details. there is just a repeated idea that 'it costs alot to run this sort of gear'. titanium valves, springs & retainers. billet ally/GRP rods, 55mm billet cam, magnesium/thin wall stainless turbos... its insane

i guess 'alot' would be quite an understatement

RB's are nice but i wanna turbo big block!

Link to comment
https://www.sau.com.au/forums/topic/44072-who-here-likes-nm/#findComment-900831
Share on other sites

iv heard about this car

that thing is street legal and competed in all the street legal drags around the states, for a little while but it was banned by all of them soon after haha just too farken quick lol :)

speaking bout big hp some guy accross east, managed to get a Marlin engine (spitfire from WWII) into a car, produces 3000hp. hehe crazy bastard!

Link to comment
https://www.sau.com.au/forums/topic/44072-who-here-likes-nm/#findComment-901001
Share on other sites

the 27L V12 Rolls Royce Merlin was in WW2 fighters such as the Spitfire, Mustang, etc. It was also used in tanks of the era.

Rod Hadfield of the Castlemaine Rod Shop fame has spent the best part of the last couple of decades engineering a Merlin into a '55 Chev body. Apparently it quite the animal. Its appeared on TV since its been finished but I still haven't seen it.

I was 15 last time I saw that car in the museum part of CRS & it was basically just a turret, chassis & engine.

Link to comment
https://www.sau.com.au/forums/topic/44072-who-here-likes-nm/#findComment-901067
Share on other sites

the 27L V12 Rolls Royce Merlin was in WW2 fighters such as the Spitfire, Mustang, etc. It was also used in tanks of the era.

Rod Hadfield of the Castlemaine Rod Shop fame has spent the best part of the last couple of decades engineering a Merlin into a '55 Chev body. Apparently it quite the animal. Its appeared on TV since its been finished but I still haven't seen it.

I was 15 last time I saw that car in the museum part of CRS & it was basically just a turret, chassis & engine.

It was on tv ages ago, can't remember what for but he was having a good talk about it . Was awesome.

Link to comment
https://www.sau.com.au/forums/topic/44072-who-here-likes-nm/#findComment-903737
Share on other sites

Guest INASNT
That's Mike Moran's car + motor there, he's a leading edge drag racer in the states who always seems to be driving customer's cars for them. Then he decided to build a car for himself, and look what he got :D

Yep that car has been in a special zoom magazine drag edition last year!

It was pulling low 6 second 1/4 times in that same shell last year

Link to comment
https://www.sau.com.au/forums/topic/44072-who-here-likes-nm/#findComment-904471
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...