Jump to content
SAU Community

Recommended Posts

Ok to keep it simple as possible with no confusion

I own a R34GT Auto

For some reason when i press the accelerator the car feels heavy like its struggling to get power, the revs dont go up in sync with when i press the pedal, almost goes to the floor before power kicks in but its still very week.

Sometimes it runs fine and this doesnt happen so this tells me its an electrical problem seeing as its intermittent. It seems to only happen on cold starts, and if i start my car hot it seems to be fine sometimes. The performance does not change during driving you have to physically turn the car off and back on.

Ran scan tool and i got these codes.

Engine: P0325 Knock Sensor - B1

A/T: Shift S/V A(P SW)


I doubt its the knock sensor so i think its to do with the transmission code but have no idea what that is.



Car has done 160,000km


Any Ideas????? Cheers

Link to comment
https://www.sau.com.au/forums/topic/440969-r34-losing-power/
Share on other sites

I am a mechanic... A knock sensor is not something that would cause power loss.

My theory it is something with the gear box like it is stuck in limp mode or something so maybe the shift solenoid needs replacing. So im thinking thats what shift s/v stands for. "Shift solenoid valve".

Could be wrong im just not sure because this problem does not throw any lights

knock sensor could be throwing it into limp mode right?

Maybe.

I don't think it would go into a limp mode as such (doesn't exist) , but would likely be running on the knock maps which are rich and have timing pulled.

And your trans is unhappy.

The knock sensor is very delicate on the 3sgte and there have been many counts of them failing once they take a high reading of knock for your information.

Im obviously aware that it is not an mr2, i am just imputing a real world experience i have gone through with simular symptoms. No need to be rude about it mate... We are all here to help after all.

Edited by asps91

Hmm doubt its CAS or AFM. Because its not throwing a primary ign code.

I wonder why its only sluggish when it starts cold but if i start it hot its heaps better.

Thinking about giving it an AT service and replace that solenoid because i know thats the reason why sometimes AT light comes on and gets stuck in 3rd (common problem after they reach 140,000)

But sluggish wise i dont think its the AT

Yes. The f**king knock sensor and the fact your trans is unhappy can't be helping.

Fix the error codes on ecu. That's why they are there.

What do you want to hear?

What do you want to fix?

Also cas or afm won't cause an ignition error code. Problems with the coil packs or coil loom will (that is the ignition system)

Edited by superben

21 is ignition code.

What have you seen that says the cas and afm don't have an individual specific code for them? Cos they have their own codes.

Maybe your research isn't up to scratch?

www.skylinesaustralia.com/forums/uploads/post-50241-1260308643.jpg

anyway,do what you want. Ignore the knock sensor code, worry about the converter etc....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...