Jump to content
SAU Community

Recommended Posts

3 grand! What a rip off!! Obviously they didn't want to do it, that's why they quoted you so much.

Yes its labour intensive as its timing belt off, cams out & the valve assemblies are recessed in the head. I would quote around the 4-5hr mark for this job.

Question 1: how smokey is it?

Question 2: how many k's on the engine?

Question 3: who diagnosed the problem?

Question 4: do you know which cylinder it is? i.e. one oily spark plug?

Statement: A possible cause of a leaking valve stem seal could be a worn valve/guide as a worst case scenario, but you won't know that till the spring is off & check the valve in the guide.

  • Like 1

3 grand! What a rip off!! Obviously they didn't want to do it, that's why they quoted you so much.

Yes its labour intensive as its timing belt off, cams out & the valve assemblies are recessed in the head. I would quote around the 4-5hr mark for this job.

Question 1: how smokey is it?

Question 2: how many k's on the engine?

Question 3: who diagnosed the problem?

Question 4: do you know which cylinder it is? i.e. one oily spark plug?

Statement: A possible cause of a leaking valve stem seal could be a worn valve/guide as a worst case scenario, but you won't know that till the spring is off & check the valve in the guide.

This is exactly what I had, had the head reconditioned all good, to the op three grand is a joke you

Can pick up a good motor for way less than that.

Check out other mechanics who know imports there's heaps in Sydney. :-)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Starter motors used to use the weight of metal (magnets) to provide torque. Now they use (more) current instead. This. It's completely normal.
    • So thing that had me stumped, but I think is OK....is that when it was up in the air, in neutral I had it running to bleed to coolant while I put the wheels back on. I noticed the rears were turning (slowly) which I'd never seen before 20250928_163512.mp4     Because there had been an issue with clutch slip due to pedal adjustment on the dyno, I assumed there was still and issue so spent some quality time upside down under the dash adjusting the pedal....but no matter what I did the wheels still turned in neutral. Even disconnected the master cylinder to pedal rod and same. In despair, I even removed the clutch slave so there was no chance of any preload causing it.....still happened. So either: 1. Something is not right in the bellhousing, or 2. Its a thing sometimes with cold, thick gearbox oil Internet says it might be 2, I hope so!
    • OK, few more things sorted and it is ready for a shakedown on 10-Oct, with one weird thing. Changed the run in oil and filter for the good stuff. 8l came out, about 8.5 went in with filter so that looks all good. Changed the starter (again), this time for a brand new one, works good. Interesting that the Taaaarks one is shorter than factory but spins harder, I guess electronics have moved on a little in the last 30 years. Will be nice to have a bit of extra space under there. Put the timing cover back on, and noted where the cam gears were set as a record.  Will need to double check the timing but it is pretty close. Also put the coil pack cover and intake snorkel back on. Exhaust Inlet Changed the water out for coolant, bled up nicely. Removed the rear brake pads (well worn factory sumitomo ones!), gave the hardware a good clean and reassembled. I've put bendix XP on the back again because the price is excellent at $150 a set and they worked well on the V37. Front pads have plenty so no issue there
    • Mine is all -12, I’m running a dry sump in a billet block though 
×
×
  • Create New...