Jump to content
SAU Community

Recommended Posts

Hi All,

Need your expert opinions. I had a forged RB26 built and run in around four years ago. Since then I had it removed and stored away. I am in the process of installing it in a new car and am wondering if there will be issues with it. I have heard from a not a very reliable source that cylinders can rust and engines can cease. Is this true? Are there tricks of the trade in getting an engine stored for this long started and going again?

Your opinions and advice is much appreciated!

Cheers.

It should have been spun manually every few mths, but in any case you could remove the spark plugs and throw like a cap full of oil in each cylinder and probably just add some thru the filler cap....But most important when its time to start unplug the cam sensor and turn it over for a while so some oil will circulate before actually starting.

It "should" be full off assembly lube and oil.

Pull the plugs out turn it over by hand

Further to the above. Leave tge plugs out when cranking it over so it doesn't kill the starter motor and wait for oil pressure to rise. Then refit the plugs and start it

The paranoid approach would be to chuck a borescope or one of those cheapearse fibreoptic cameras down a couple of plug holes to look at the bore walls. If there's any rust it should be visible. If there's not visible, breathe a sigh of relief and continue on as normal.

Do the manual lubing stuff described by the guys above before trying to get it going.

Brilliant guys!! Appreciate all your input. My brother has a micro camera GTSBoy so as a sanity check I might do what you suggested before I do what everyone else suggested in the way of lubing the engine again.

Thanks again all!

Definitely check the cylinders out, then I would throw some oil in them regardless, hand turn it over or use the starter with no spark plugs in.

Or you could just start it, probably will run fine and you'll know soon enough if it had enough oil/had any rust in it! (don't do this)

The obvious thing is chance all the fluids as well.

Edited by Rolls

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
    • I take it that the knock retard is from bearings tapping a little tune? Thicker oil is a fragile bandaid. You need a much bigger oil cooler and probably the bigger pump being discussed.
    • Hi @Chupapy i had several leaks from coolant pipes being corroded, i also had one leak on back of the head onto transmission. For me that leak was from the turbo water line. Follow the line to the back of the head The hose and metal pipe had perished these are the best pics I took of it at the time
×
×
  • Create New...