Jump to content
SAU Community

Recommended Posts

joying ? By any chance

Yes it is. :). Only complaint is the radio audio quality is average. But I steam internet radio instead. That sound quality is extremely good. You also need a pac nis02 bose adaptor to get rid of the hiss.

I would get a unit with second zone video out to feed to the OEM screen with HKS OBD LINK Or Hobdrive data.

Matt

Hey everyone, is there a pin out for the rear of the TV Tuner or anyone able to tell me which plug is for what? I would say the grey one is power and the RCAs are obviously Sound (picture too)? I'm gonna guess the grey, green, black and red near each other are possibly the aerial? I may be wrong on some of that but still not sure what the rest are if I am right, any help would be great.

Cheers

black coax are diversity antenna's

Red will be right audio in

White will be left audio in

The other plug on the green wire will be video

The shield / braid of both the audio wires (red & white) are connected together. The shield of the video (yellow) is on a separate pin.

This is the layout of the white socket on your tuner:

1________6

2__3__4__5

1 - audio right (red - inner conductor)
2 - audio left (white - inner conductor)
3 - audio ground (shield of both red & white above)
4.- video (yellow - inner conductor)
5 - not used
6 - video shield (yellow - outer sheild)

Thanks. So the RCAs are in not out, hmmm wonder what's going in? Possibly the DVD player in the small section above the glove box? I thought the DVD player would link straight into the back of the pop up screen? Also what's the White plug above the grey power plug/cable? Anyone know how many amps it uses? I know it's 12V not sure on Amps. Thanks!

dvd player is gps nav only.

the plug with the red/white av leads is aux on the factory radio and VTR on pop up screen.

you must have an aftermarket device fitted looking at those connections.

only some models came with reverse camera.

Edited by conan7772

dvd player is gps nav only.

the plug with the red/white av leads is aux on the factory radio and VTR on pop up screen.

you must have an aftermarket device fitted looking at those connections.

only some models came with reverse camera.

Yea the aftermarket device is the DVD player above the glove box, someone has ripped out the factory one and installed a DVD player which works perfectly (sound and picture). When I change to TV/DVD the factory head unit automatically changed to AUX, now I'be got an aftermarket head deck and need to look at changing around some wiring/cables/plugs etc. Also looking at ditching the stock TV tuner in favour of something more modern and powerful.

The signal has to be in Xanavi language.

You'll lose all the functions of the pop up display.

Unless you start from scratch: New tuner, new head unit, new lcd screen.

How is the video and sound input to the screen/stereo? RCA/s in the rear of the LCD?

I want to keep all the trip computer stats/ fuel economy features etc on the factory screen.

Thought about a new head unit, quite a few people crack the fascias pulling it all out.

If you've got good sound and picture through your dvd, you're laughing.

I think the factory head unit sounds pretty clean.

My days of 4 channel amps and 10 inch subs are over.

I've changed the factory head unit, working on fixing the sound from the DVD as the plug is an 8 pin mini din, which I need to convert to an aux/3.5mm headphone. Other than that the DVD is good it's an old aftermarket unit but that's fine

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The average previous owner for these cars were basically S-chassis owners in the US. Teenagers or teenager-adjacent. I often tell people that neglect is easier to fix than something that was actively "repaired" by previous owners.
    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
×
×
  • Create New...