Jump to content
SAU Community

Recommended Posts

Hi guys, after selling my r33 gtst about 6 months ago, I realised that after driving a truck all week that I need to not drive a truck on the weekends. Anywho, I have just found a beautiful 1996 GTR in Japan that I am having shipped over.

I thought there was a thread on 'what maintenance to do when your car arrives from Japan' but I cant seem to find it. If anyone knows the thread I would appreciate it if I could be pointed in the right direction :)

If there isn't one, I was thinking that I should get the vehicle checked out once it arrives, just to note any issues the car may have that I do not yet know about, to change the oil, oil filter, air filter and fuel filter. Have the timing belt looked at to see if it has been changed and the condition, and as soon as is practicable to get the rest of the cars fluids changed. Anything else I should think about in the meantime? I was thinking I can get all the necessary parts while waiting for the car to arrive.

Thanks guys.

post-75846-0-56460600-1397377279_thumb.jpg

Edited by ima_slap_joO

All consumable parts would be in summary a good start, of which fluids and belts as you have already mentioned. Further to that, you could check hoses, ignition coils and spark plugs and perform a compression/ leak-down test while apart.

Is it heavily modified or stock? Personally I wouldn't bother going way over the top replacing a whole host of parts, since you can begin replacing parts with upgraded or new parts as you go e.g fuel and ignition, alloy radiator, turbo etc.

Provided that the engine is in good shape (as tested from the compression/leak down) you'll know your working from a good base. Maintain it (oil/ fluids) and upgrade supporting mods (injectors, driveline bushes/clutch) as required to meet your goals (power/ application: street, circuit, and drift)

Hi 75coupe, you didn't need to type full in quotation marks, it makes it looks like you are implying I shouldn't have a full service.

Some things are not obvious, like rusted out pulleys that I only thought of once searching. There may some good ideas coming from members that I could have a look at whilst I am getting the car ready.

Yeah that sounds like a good idea, I will have a compression test done while I am getting the service. The car is completely stock, upgrading items on failure or items that are on the way out seems to be the way to go, the car wont be driven very much, only a couple of times a week.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...