Jump to content
SAU Community

Recommended Posts

i have compete RB26DETT engine for sale,

was going to built for big hp engine,due to not use it,

engine is still running nothing wrong for it,

the only damaged on this engine is drop the compressure at last 2 cyclinder,

here is the report for the compressure test:

1st = 155

2nd =156

3rd =160

4th =159

5th =105

6th =104

i am asking $3000 for this complete engine,come with everything,inc intake manifold and throttle bodies etc.

have a quote for Std rebuilt around $2500 or less,

if anyone interest,plz let me know

Link to comment
https://www.sau.com.au/forums/topic/44237-broken-rb26dett-engine-fs-3000/
Share on other sites

i have compete RB26DETT engine for sale,

was going to built for big hp engine,due to not use it,

engine is still running nothing wrong for it,

the only damaged on this engine is drop the compressure at last 2 cyclinder,

here is the report for the compressure test:

1st           = 155

2nd          =156

3rd           =160

4th           =159

5th           =105

6th           =104

i am asking $3000 for this complete engine,come with everything,inc intake manifold and throttle bodies etc.

have a quote for Std rebuilt  around $2500 or less,

if anyone interest,plz let me know

what model did it come from ? r32 ? 33 ?34? does it come with turbos ? dumps ?starter ? alt ? steering pump ? can you send me pics ?

email [email protected]

tnx jerry

ps you cant rebuild for $2500 , pistons and rings are $1200-1300 gaskets 350 and you havent even looked at crank , cil head .

wrxhoon : i have quote to rebuild the engine,coz its drop the compressure and the engine builder said its only piston ring and just replace that and rebalance the engine,nissan head gasket only cost $250,everything wil cost around $2500,

also the engine are less turbo,its off R32GTR.dont have any pics,if you are serious for the engine,i wil take some pics,

will sell all the parts separte:

head with all the rock cover $1500

STD cam shaft $300

STD injector with fuel rail $350

valve spring $50

piston $200

oil pump $100

water pump $50

conrods $400

Crank shaft $450

block $450

exhaust manifold $150

intercooler pipes(Twin Turbo writing on it) $150

all the water fitting on turbo side $90

intake manifold $600

throttle bodies $500

sump $120

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I am well aware as I did rant at him to buy a MX5, buy the 2.5 before he DIY'ed it, etc as well as do things to the holden. He will obtain a ND. It's the best of both worlds. They look great in person, definitely the best looking one. Just a matter of time now.
    • Remember this is the same person who said he’d never own an nc 
    • ouch! how is the car now?I had sold my gtr but have been looking into some on trademe and a 260RS but I wouldnt be keen on any repairs needed on them
    • This sounds like someone who would have owned an R33 in their past... It's okay, I'm 100% picking up what you're putting down Mark.
    • Just back on what was raised about jacking off the the tow/tie down point on the front of cars. I've used it plenty. I've also watched it on a car where you could see it move the front end of the car. It was like the front end/whole car being tweaked and twisted a bit. I will say, I struggle to find good jacking points on MOST cars. The ones that have good points, I then normally struggle to find a jack tall enough to make the car change height!   One of my go to points for either the jack, or the axel stands though, is either a suspension pickup point, OR a subframe to chassis major bolting point. I actually think its the subframe on my R33 that has a bit of a bend in it, from being jacked in the middle too. However, it could have been one of my many other cars I've had over the years! Or it could also be the from me jacking it up, and the fact the top of the front radiator support isn't there, so it can allow the front of the car to move and bend etc.
×
×
  • Create New...