Jump to content
SAU Community

350Gt Power Window Problem?

greychocobo
 Share

Recommended Posts

greychocobo Explorer

greychocobo

Posted
Posted

Hey there guys I've recently have this window problem just wondering if any of you guys have faced a similar issue and know how do i fix this. It started when my door actuators died so I brought my car to a car electrical shop. They tested popped up the bonnet and connected a lead to test the wiring system under the steering and inside of the door trim. after testing they said my alarm module might have died or something and my actuator's dead. (I've already told them in the first place that the actuators dead and thought they might have a universal one and mod it into my car). so i've never heard from my mechanic that my module was dead before so i said ok. they screwed back my door trim and i drove back home. half way out of the shop i noticed my power window (driver side) does not go up automatically. it only goes up manually. and when either door (passenger/driver) is opened, the window drops down like 1/4. I'm not sure what caused this and any advise would be great.

on a side note i brought my car to my mechanic and they tried the "reset" method after doing some research on the net and it still didn't work. window still drops when the door is open and stays there when closed.

i was pretty pissed as i paid 90$ to the so called electricians to "diagnose" my car's problem to get the windows not working. now I'm lost on what to do next. any advise?

Link to comment
https://www.sau.com.au/forums/topic/443292-350gt-power-window-problem/
Share on other sites
Chris Rogers Grand Master

Chris Rogers

Posted
Posted

Get the credit card out and bend over. That's not going to be a cheap exercise. Both door looks and both window motors need doing on top of the stereo you asked me about. Get ready to shell out $2k .

Howaitonaito Mentor

Howaitonaito

Posted
Posted

If it gets stuck down and you want it to go up. Open the door and while holding the Window switch up close the door with a bit of force (don't slam it) and that should do it.

Works everything for me.

The motors and regs in these doors are common fault. Reg + motors new from Nissan are about 800 for the both per door (give or take I bit)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Sorry. Front brake calipers
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • DraftySquash
      Looking for someone with a R34 front bar

      By DraftySquash · Posted

      Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
×
×
  • Create New...