Jump to content
SAU Community

Recommended Posts

Wrecking, White 1999 Nissan Stagea. Factory Manual AWD with RB25DET Neo. 130,xxx km.

These are a few specific things available:
- $2200 RB25DET Neo AWD engine with about 130,000km (head gasket, timing belt, water pump etc were replaced at 100,000km - compression test to come, can hear running)
- $600 Standard ECU with NISTune Type 2(?) board.
- $600 Full set of R33 GTST brakes including 4 pot front calipers, 2 pot rears, non-warped rotors, good pads. Will not split anything.
- $600 full set of white 17x9inch Yokohama AVS Model 6 wheels. one has slight gutter rash. Unsure on offset, maybe +35? Front tyres still have legal tread (Federal 595 EVO), rears cooked. (pictured)
- $100/pair front guards, not rolled, mint condition.
- $150/pair rear doors, mint condition, no rust, including glass and door trims.
- $200 Series 2 tail lights and garnish, mint condition.
- $150 Manual dash cluster with 130,000km, mint condition.
- $80 climate control unit, mint condition.
- $350 3 inch mandrel bent mild steel exhaust with stainless Varex muffler with twin tips (no controller). might suit other cars.
- $400 standard RB25DET Neo turbo (OP6 rear), holds boost fine, never boosted past 10psi.
- $20 hot side front mount intercooler pipe, alloy.
- $80 standard AFM (slight damage, does not affect use).
- $150 tail gate including glass. mint condition, good gas struts, no wing or lights/garnish.
- $50 bonnet gas struts, excellent condition.
- $400 rear subframe, including hicas, viscous(?) diff, pump, etc, never had any issues (can separate diff and sub frame).
- $80 full set of floor mats. passenger side slightly worn, rest are mint.
- $50 rear bumper bar. standard, mint condition.
- $60 Turbosmart boost gauge, PSI up to about 20 or 25psi.
- $50 3 inch stainless decat pipe.
- $offers dash, no cracks or fading. mint condition.
- $80 ~350CCA battery (exide brand, maybe), couple of months old. Was $150 new.

Everything else available EXCEPT the following (THESE ARE NOT AVAILABLE):
- Complete Manual conversion (gearbox, pedal box, clutch, clutch master and slave cylinders, hydraulic line, flywheel, tail shaft, front prop shaft).
- Front doors
- stock airbox
- torque split, volts and boost gauge (factory)
- front struts (standard all round)
- front seats
- cargo blind
- cargo net (never had it)
- steering wheel (air bag deployed)
- headlights
- indicators
- front bar and rio, radiator, clutch fan, shroud, alternator, bonnet.(destroyed)
- stereo...

Prices are firm.
Items located in Hobart. Can post smaller items at your expense. Items listed elsewhere also. Can provide pictures upon request of most, if not all items.

Righto, whole car has been sold.

Still have the wheels (Cpl.custard - please send me your mobile number and i'll send a pic of the wheels), and still have the full set of floor mats.

Cheers,

Ian.

  • 3 weeks later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...