Jump to content
SAU Community

Recommended Posts

Bob you'll need to specify the model.

There's pre 91, post 91 and N1.

Ok....... I need both pre and post 91's for my ADM and V-Spec2.... N1 not so important.

I know the High beams are the same H3's and the Low beams are H3c and H1 respectively but I want to know the wattage.

Thanks,

Bob.

The 85W bulbs are std....... I had it checked out with Nissan yesterday.

I bought some "you-beaut" Phillips globes as the cars going back to Unigroup on Monday and I figured they can throw them in for me but..............

In the box of goodies I got from the previous owner there is a pair of H11 globes and a pair of HB3's..........

I'm hoping that it's just a coincidence (and error) that he gave them to me as I can't see anywhere our cars taking these globes.

A post "91 car should be H1's and H3's and these are for my V-Spec 2.

This is what I bought, I couldn't get The H1's in 85W bar Nissan and I wasn't going to pay $77.00 for a pair!

I could get 100W but it's risky putting more load on the wiring.

I got these 55W but with extra 60% coverage according to the box! How often do I use high beam....... Not often.

Hopefully they all fit.

Bob.

post-78207-0-25292700-1401522558_thumb.jpg

post-78207-0-74985700-1401522563_thumb.jpg

Bob did Nissan check the factory fitment in Japan or the upgrade as fitted to the Aus model?

The Aus model had 85W fitted as part of the changes to suit our "challenging" driving conditions.

I've only seen 55W in my 32's, even the N1 has moderate wattage of 60/55W in their H4 bulbs.

Bob did Nissan check the factory fitment in Japan or the upgrade as fitted to the Aus model?

The Aus model had 85W fitted as part of the changes to suit our "challenging" driving conditions.

I've only seen 55W in my 32's, even the N1 has moderate wattage of 60/55W in their H4 bulbs.

Hmmm...... Good point....... My parts guy knows I have 2 cars but may well of quoted based on the ADM.

Maybe the later cars got this upgrade too?

I'll know more tomorrow after they hopefully fit what I will give them.

I'll let you know.

Bob.

I probably should have just looked in the owners manual instead of digging bulbs out of suspect headlight assemblies !!!

Well...... That's our answer well done........ I think. What does the 2 and 4 mean on the top two lines?

Thanks,

Bob.

My handbook is for all model Skylines and I think sedans had a combination headlight which used the H4, thus only 2-headlights.

My car has individual low beam lights and high beam lights, thus 4-headlights.

I can't read Jap, so I'm just guessing.

The next light below (with the H3 12v/55W) would be for the fog light.

But Bob your question is doing my head in.

Handbook says H1 on high beam.

To my knowledge R32 projectors use either a H1 or a H3C on low, but they all use a H3 on high??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...