Jump to content
SAU Community

Boiling And Leaking From Coolant Overflow

Roachiie

By Roachiie,
in General Maintenance

 Share

Recommended Posts

Roachiie Apprentice

Roachiie

Posted
Posted

Recently got a greddy plenum and 80mm throttle installed on my r33 rb25 and while driving home from the shop my overflow fills up boils and sprays water my radiator empty but no leaks anywhere on the radiator or pipes coming off it's like it's all being sucked into overflow tank then blown out

Any ideas ???

Ben C34 Grand Master

Ben C34

Posted
Posted (edited)

But don't u get oil through the coolant and blows smoke if head f**ked

No.

Depends on where it has blown and how bad.

It could be that the cooling system wasn't bled correctly.

How much power did you lose/gain from fitting the plenum?

Edited by Ben C34
533 RYC Proficient

533 RYC

Posted
Posted

What Ben said David.

Re bleed the cooling system. Corrections may have to be made due to the changed heights of bleed points (if any).

Radiator cap could be a possibility as Callan stated, but would have shown an issue previously.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Looking for a part number for this part here

      By Duncan · Posted

      So....to find any R chassis part number, get your VIN (will be something like ER33-xxxxxx for you) and go to: https://www.amayama.com/en/genuine-catalogs/nissan and enter it. From there you have access to a web version of Nissan's part system, FAST. It is a bit tricky to get used to, so maybe have a shot and post up what you think.  You can also search by general model but note in some cases your car might have different options so VIN is safest.  On diagram 211 I got 14075-75T16 for Connector, Water Hose If I search for part 14053‑21U10 that you posted, that is also a water hose but not the one bolted to the plenum and 14075‑04U00 is the fitting where the water hose goes into the block.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Yeah now we are talking I much prefer coolers in the front middle because it lessens the chance of a small bump to a corner stopping the whole event. I was thinking the AT cooler can move out of the radiator, delete the AT/engine coolant interwarmer and mount a separate cooler with a thermoswitch somewhere further back as is common in racing, that would be one thing. Beyond that, the engine oil cooler is an obvious one to move to the wheel arch, potentially one on each side, but unused space is an issue. I did have a earlier pic with the bumper off but it doesn't show how busy the corners are: DS is full of the auto driving sensors and PS is totally fully of windscreen washer fluid reservoir But ultimately I was hoping to keep the AC, and the water/air heat exchanger is fundamental so it is not just the radiator that needs to be in front BTW here's airflow to the rad as it ran at the track (one horn is gone now and I'll remove the lights next time):
    • turboedsloth
      New Wasteland Wa Topic

      By turboedsloth · Posted

    • V35_Paul
      Infiniti Q60 Navigation Update

      By V35_Paul · Posted

      your right the maps for Australia came out in 2017 but are 2010 maps. i got the updated maps SD card put it in and it was the same. Same maps in my Brothers Nissan Patrol. 2020 i think his car is
    • silviaz
      Returning after a long time!

      By silviaz · Posted

      Yeahhhh, the costs have killed me. Spent more than the cost of an engine rebuild and it most mostly servicing and a tune lol.
×
×
  • Create New...