Jump to content
SAU Community

Recommended Posts

Hello

I have read about putting rb25 turbos onto rb20's. One thing I cannot find a clear answer to is if the engine needs to be tuned to run it.

Is it ok to run a rb25 turbo on a r32 gts-t rb20 engine without a tune for a couple of months?

My mods I have are full turbo back 3inch exhaust with a sports cat and split turbo pipe, pod, and the return flow fmic.

I am going to put in a new aftermarket fuel pump such as a Walbro or Tomei.

The rb25 turbo that I have has the HKS actuator on it.

I live in Japan so not so hot as it is in Australia.

Will I be ok running the rb25 turbo on this set up?

Edited by yoshiii335

It will be fine, my 25 turbo has been running 16psi on the stock ecu for 2years now with no problems

Oh, youve been running 16psi? I thought they were not good over 1 bar before they run high risk of breaking?

What kind of response and power have you gotten without a tune?

Edited by yoshiii335

Oh, youve been running 16psi? I thought they were not good over 1 bar before they run high risk of breaking?

What kind of response and power have you gotten without a tune?

Well without putting the car on a dyne before and after (and then why wouldn't you get a tune anyway?) you won't be able to tell apart from the seat of your pants.

You can run the turbo over 15psi but there's obviously a much higher chance of it falling apart. 12-14psi is usually what is considered safe.

Car made 130kw atw and now has 170kw atw, i have herd the same thing about not going over 1bar. I have been keeping an eye on it and there is no shaft play and not blowing any smoke, being a auto may help take some wear and tear of it though

The 1 bar limit is the apparent safe limit on an rb25.

On an rb20 one would assume you could run more boost, as it is shaft speed that destroys the turbine, not boost pressure.

O.P. is apparently using stock ecu so anything much higher than 1.0 bar (depending on weather conditions) will probably have it coughing and farting.

I fitted a 25 turbo on my 20 in the Rustia, used the 20 actuator and it went very well.

Added a bleed valve to increase boost and it didn't like it. So I left it at the stock 20 actuator boost but reading the signal after the cooler.

Obviously the 25 turbo is not working as hard to pump a given boost on the 20 as it was for that same boost on the 25.

A good cheap upgrade for a 20 in my opinion.

FWIW, I ran my sietbox 180SX (RB20DET) back in the day with a RB25DET turbo at 1bar on the stocker ECU.. went alright, until I got a CEFF1E remap (not sure if he is still around) and the car started to wake up

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Man, different parts but the same numbers is terrible @dbm7! And it doesn't help that most online shops don't list the part numbers at all. They just give a list of compatible models...
    • Slow when hot could also be because its getting more dynamic compression, OR things are getting a bit tighter once it is all expanded. If it were an earthing issue, typically I'd expect you to have it have issues all the time. Unless it's really a combination of both things. Where the higher compression, and things being a bit tighter, is giving that bit of extra load and you do need a slight clean up on the cables/connections.
    • Yeah, this is one of the most annoying things about nissan part numbers... I've got an unrelated example... Image is of the AT output shaft ~ they have the same part#, but clearly the shaft on the left is beefier design to that on the right ...the difference (essentially) is the 'lighter' shaft on the right, is for engines up to RB25DE (this includes RB20 variants) : the shaft on the left is for RB25/26DET(T)....are they interchangeable? Yes...but obviously one shaft is going to be stronger than the other...and, the lighter shaft is around USD115, but the heavier shaft closer to USD150...same part#... ...epc-data usually tells a tale ~ the amayama listing for 39100-23U60 has a note "Longest side is between 60 and 105 cm" ; no such info is there for 39100-23U70 ...and given the great disparity in price between the 2 parts, it makes me at least curious (to the point of caution) where the 'extra money' went? ...ie; these 2 parts have a cost difference that (to myself at least) isn't explained by 'plastic boot'...ie; with amayama there's AUD700 price difference ...plastic versus rubber?...I'm not seeing it like that...and 60cm ~ 105cm...??...that's a huge disparity....something hinky going on here... I'd try searching by VIN, not model... /2cents
    • I don't know for sure, but I'd expect them all to be interchangeable given the diff end and hub end don't move/change between any C34 series. Often Nissan will change part numbers and the aftermarket follows those year ranges; but the original part number change doesn't mean other parts won't fit. The change could be a change in material, internal parts or even just supplier. For example, all the RB gearbox to engine bolts are no longer available and there is a new part number instead. The only change is they went from cadmium plated bolts to zinc plated due to the issues manufacturing with Cadmium. They look different but work the same.
    • One year is a bit concerning. Did you try contacting GSP? It says 5 year warranty on the box if I remember correctly. I'm also running their driveshafts on my S2 Stagea.   You could check the part numbers on Amayama for your year. Here's the link for my 1998 which gives the 39100-23U60 part number. Well, that and 39100-23U70. https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6649-rb25det/trans/391 What does it say for yours?
×
×
  • Create New...